Sport Flyers Simple Stick EP Скачать руководство пользователя страница 1

1

Simple Stick EP Specifications:

ASSEMBLY INSTRUCTIONS

Kit Product Number  160522

The Simple Stick EP is what we have nick named the A-ARF.  This is an airplane with many things done for you, but it is not quite
an ARF.  Why?  You still have to put the color on the foam, so the finish is up to you!  You can leave it bare foam or you can apply
the included colored tape as your finish (which makes the airplane very strong, too).  You can use different colored rolls of tape to
achieve the color scheme you want, or you can even cover it with low-temperature covering material like Econokote!

The Simple Stick EP is built to be easy and versatile.  It is quick to finish, can use a wide selection of mini and micro radio gear,
and will fly on many power systems ranging from a 370 geared motor to the KMS 31/21 brushless motor and 18 amp ESC.
Regardless of the power system you choose, we recommend using a lightweight LiPO battery.  In this size range, LiPO batteries
and chargers are affordable and reliable.

In the air, the Simple Stick EP is simply a pleasure to fly.  The light wing loading, thick airfoil and 4-channel controls make it
suitable for both new pilots who want to learn to fly aileron airplanes and sport flyers who love aerobatics.  Because of its size,
large parks, school yards and other small outdoor areas are perfectly suited for the Simple Stick EP.  No matter your skill level is,
this is a fun plane you're going to enjoy flying!

Functions:

  Ailerons, Elevator, Rudder and Throttle

Motor & Battery Required: 

 See Suggestions on Page # 4

Radio Required:

  4 Channel or More w/4 Micro Servos & Micro Rx

ESC Required:

  Dependent on Motor and Battery.  See Page # 4

Wing Span:  

42.9 Inches (1090mm)

Wing Area:  

378 Square Inches (24.41dm

2

)

Length:  

31.8 Inches (808mm)

Weight RTF:  

20 - 25 Ounces (566 - 710gr)

Wing Loading:  

7.6 - 9.5 Ounces/Square Foot  (23 - 29 g/sqdm)

Содержание Simple Stick EP

























Отзывы: