background image

Page 4

Safety Rules

 

WARNINg

Remember, any power equipment can cause injury if operated 

improperly of if the user does not understand how to operate the 

equipment. Exercise caution at all times when using power equipment.

General Safety

 

y

Read and understand the instructions in the owner's manual before operating the log splitter.

 

y

Never allow anyone who has not read and understood these instructions to operate the log splitter. 

 

y

Never allow more than one person at a time to use the log splitter. The same person should both load and 

operate the log splitter. 

 

y

Never allow children to operate the log splitter. 

 

y

Never allow children in the area while the log splitter is running. Stop the engine if a child approaches.

 

y

Never allow bystanders in the area of operation when the log splitter is running. 

 

y

Never operate the log splitter without all guards and covers in place.

 

y

Do not modify the safety controls. Make sure they are operating properly before each use.

 

y

Do not make any modifications to the log splitter.

 

y

Do not use this log splitter for any purpose other than splitting logs.

 

y

Do not exceed the manufacturer's recommended capacity of the log splitter.

 

y

Always check for loose nuts and bolts before each use and tighten any that are found to be loose.

 

y

Always wear safety glasses or goggles while using the log splitter.

 

y

Never wear loose fitting clothing or jewelry while operating the log splitter. 

 

y

Wear snug fitting gloves while operating the log splitter. 

 

y

Never operate the log splitter while barefoot or while wearing sandals. Always wear protective shoes with 

non-skid soles while operating the log splitter. Safety toe shoes are recommended.

 

y

Always wear hearing protection when using the log splitter for prolonged periods of time.

 

y

Only operate the log splitter on a flat, level surface with secure footing.

 

y

Always shut off the engine and make sure all moving parts have come to a stop before making adjustments.

Engine Safety

 

y

Always keep hands away from the engine, belts and pulleys when the engine is running.

 

y

Never run engine in an enclosed area. Adequate ventilation is required to prevent carbon monoxide 

poisoning.

 

y

Do not fill the fuel tank indoors, or while the engine is running or while the engine is hot. Reinstall the fuel 

tank cap and wipe off any spilled fuel before starting the engine.

 

y

Do not store the log splitter near an open flame or a heat source when fuel is left in the tank.

 

y

Do not operate engine with air cleaner or cover removed. Removal of these parts could create a fire hazard.

 

y

Never change the engine governor settings.

 

y

Always allow the engine to cool completely before making adjustments or repairs or cleaning. 

 

y

Always disconnect the spark plug wire before making adjustments or repairs. Keep the wire away from the 

plug to prevent accidental starting. 

 

y

Always allow the engine to cool completely before covering or storing in an enclosed area.

Towing Safety

 

y

Do not exceed the 45 mph while towing the log splitter.

 

y

Always use safety chains when towing.

 

y

Always check that coupler handle is locked before towing.

 

y

Always use correct ball size that is stamped on coupler.

 

y

Check coupler tightness before towing and after towing 50 miles. Adjust locking pressure as required.

 

y

Always check coupler and ball for damage before towing. Replace if damaged.

Содержание 45-0503





















Отзывы: