manualshive.com logo in svg

Splicecom 4100, Инструкция по установке и обслуживанию

Kestrel 4100 - Компактный и точный прибор для измерения погодных условий. Получите бесплатное руководство по эксплуатации с инструкцией по быстрому старту. Скачать его с manualshive.com и начать использование сразу. Необходимый инструмент для путешественников и любителей спорта на открытом воздухе.

Поделиться
Скачать
background image

Installation and Maintenance Manual

 

 

 

Configuring system functionality 

Installation and Maintenance Manual v4/0615/10 

 

103 

 

 

 

Users can also add and edit their own personal 

numbers via their PCS 58x, 57x, 56x, 55x, PCS 410/400, 

PCS 60 or PCS 50.  This facility is controlled by the Edit 

Mode field under the General Page.  By default this is 

set to All which gives the User full rights to edit his 

Number fields.  However this right can be disabled by 

selecting No Personal Numbers from the list box. 

 

 

 

 

The No Personal Numbers option will also disable the User’s ability to edit his Description field via a 

PCS 58x, 57x, 56x, 55x, 410/400, PCS 60 or PCS 50. 

 

The Home Page field determines which web page wi

ll be displayed as default on the User’s PCS

 58x, 

410/400, PCS 60 or PCS 50.  This could be a page stored on the internal web server (please refer to the 

Internal Web Server section from page 264 for further details), the custo

mer’s intranet or accessed 

externally if an Internet connection is available.  

 

Using Follow Me 

The Follow Me feature will allow a User to take calls, for example, on their mobile or at home, when they 

are out of the office or at another extension if, for example, the User is spending the day in another part 

of the building or in another office. 

 

Setting Follow Me 

1

 

In Manager select Users 

2

 

Select the User you wish to configure 

3

 

Select the Telephony page 

4

 

From the Follow Me list box select one of the following options: 

a

 

None 

–

 calls will not be forwarded 

b

 

Personal 

–

 

all calls to the User’s extension number and DDI will be forwarded

. 

c

 

Dual Personal - 

all calls to the User’s extension 

number and DDI will be forwarded, and the 

User’s extension will ring.  (Calls to the User’s Department(s) will ring on the User’s extension.)

 

d

 

All - 

all calls to the User’s extension number and DDI will be forwarded plus any calls to a 

Department to which the User is a member. 

e

 

Dual All - 

all calls to the User’s extension number and DDI will be forwarded plus any calls to a 

Department to which the User is a member, and the User’s extension will ring.

 

f

 

Personal External - 

all external calls to the User’s extens

ion number and DDI will be forwarded. 

Содержание 4100























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4100

NEC HX4500 Configuration Manual preview
HX4500
Бренд: NEC Страницы: 74
NEC Express5800/T120e Quick Start Manual preview
Express5800/T120e
Бренд: NEC Страницы: 6
NEC Express5800/T120e Getting Started preview
Express5800/T120e
Бренд: NEC Страницы: 2
NEC Express5800/T110i Getting Started preview
Express5800/T110i
Бренд: NEC Страницы: 2
NEC EXPRESS5800/R320d-E4 Configuration Manual preview
EXPRESS5800/R320d-E4
Бренд: NEC Страницы: 19
NEC Express5800/R320d-M4 Series User Manual preview
Express5800/R320d-M4 Series
Бренд: NEC Страницы: 98
NEC Express5800/R120h-2M Getting Started preview
Express5800/R120h-2M
Бренд: NEC Страницы: 2
NEC Express5800/R120f-1E Use Precautions preview
Express5800/R120f-1E
Бренд: NEC Страницы: 12
NEC Express5800/R120d-1E Hardware Specification preview
Express5800/R120d-1E
Бренд: NEC Страницы: 2
NEC Express5800/R110i-1 Getting Started preview
Express5800/R110i-1
Бренд: NEC Страницы: 2
NEC Express5800/R110h-1 System Configuration Manual preview
Express5800/R110h-1
Бренд: NEC Страницы: 40
NEC Express5800/A2040d Configuration Manual preview
Express5800/A2040d
Бренд: NEC Страницы: 83
NEC Express5800/320Lc Datasheet preview
Express5800/320Lc
Бренд: NEC Страницы: 4
NEC Express5800/120Rj-2 Datasheet preview
Express5800/120Rj-2
Бренд: NEC Страницы: 2
NEC NEAX2000 IVS2 Manual preview
NEAX2000 IVS2
Бренд: NEC Страницы: 106
NEC Express5800/T120d User Manual preview
Express5800/T120d
Бренд: NEC Страницы: 153
NEC Express5800/T110g-S User Manual preview
Express5800/T110g-S
Бренд: NEC Страницы: 128
NEC Express5800/R120g-1E Maintenance Manual preview
Express5800/R120g-1E
Бренд: NEC Страницы: 224

Бренды по названию

Популярные бренды

Загрузить еще бренды