background image

6

Installation

Voltage Selection

Before connecting the Gemini Mastering M/S Processor to the mains, make sure that the 
voltage selection corresponds to the values of your local power grid (230 or 115 volts). 
Inside the power connector, to the right, next to the on/off switch, there is an opening 
that displays the voltage selected. If the voltage indicated does not correspond to the one 
required, change it by following this procedure: 

Open the power connector lid with a small screwdriver (use the tiny slots on the right hand 
side). Use the screwdriver to lever the red fuse holder from above until you can grab it. 
Take the fuse holder out and replace the fuse with one corresponding to the local power 
grid specifications. You can find the adequate values on the rear of the unit or on page 16 
of this user‘s manual. Turn the fuse holder around 180 degrees and place it back again. 
When you close the lid again, you should see the correct voltage displayed in the opening. 

On the product site on our website (https://gemini.spl.audio) you will find a video con-
cerning the topic “Changing the mains voltage”. If you ever have to exchange a fuse, we 
recommend the video “Exchange defective fuses”.

First Steps

Before turning on the Gemini Mastering M/S Processor you must first connect the included 
3-pin power cord to the 3-pin IEC socket. The transformer, power cord and IEC socket all 
comply to the VDE, UL and CSA regulations. 

The Gemini Mastering M/S Processor should not be installed in close proximity to equip-
ment  that  emits  magnetic  fields  or  emanates  heat.  Avoid  exposure  to  heat,  moisture, 
dust,  and  vibrations.  Do  not  install  the  Gemini  Mastering  M/S  Processor  close  to  any 
power amps or digital processors. Instead, install it in a fully “analog rack” where any 
interferences can be avoided (Word Clock, SMPTE, MIDI etc.). 

The unit should be powered off before connecting or disconnecting any cables or equip-
ment to it. 

Use the On/Off switch on the rear panel to turn the unit on or off. The illuminated red LED 
in the middle of the front panel indicates the unit‘s operating status. The On/Off switch 
was placed on the rear panel to avoid any emissions due to voltage-carrying conductors 
running across the unit and affecting sound. When powering on or off, there‘s no need 
to observe a specific sequence regarding the connected devices. However, like with any 
audio signal chain, power amplifiers should always be powered on last and powered off 
first. The Gemini Mastering M/S Processor can be powered on and off with the use of a 
circuit breaker, as long as the total load does not exceed the rating of the latter. 

Содержание Gemini 1720























Отзывы: