manualshive.com logo in svg

SpitJack P80 Rotisserie, Руководство пользователя

Поделиться
Скачать
SpitJack P80 Rotisserie Скачать руководство пользователя страница 4

 

Support pipe A fastened into tripod base 

 

Base and pipe assembly B  

(Ready to accept the motor mount assembly) 

 
 

2.

 

Place the motor mount assembly in the spit support pipe assembly B (above). Note that there 
is a notch in the motor mount base connector pipe that must be aligned properly with the 
cross screw in the support pipe that it sits in (below). If these are connected properly, the base 
will be positioned (one leg will be directly under the motor assembly and in parallel alignment) 
so as to prevent the motor and base assembly from tipping over. Make sure that the motor 
mount assembly pipe (with notch) is fully seated in the pipe and that the alignment with 
the base is correct (see picture below). 

 

 

Cross screw in support 

pipe 

(top view)

 

 

Motor mount assembly showing notch on 

connector

 

Alignment of motor (top view)

 

 
 

Final assembly procedure:  

Note: at this point you would most likely have rigged the hog to the spit 
(see below). 

1.

 

Set the spit up so that it is resting on both supports, with the 
bearing rings seated into the spit supports. 

2.

 

Place one end of the spit in the spit coupler (attached to the 
driveshaft of the motor) and secure it with the screw provided. 
Push the screw through the coupler and the spit and secure tightly 
with the wing nut. 

Spit seated on support (1) 

 

4

Содержание P80 Rotisserie























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды