background image

 

© 2018 Spireon, Inc.

5

 / 

12

 

 

antenna 

Power Inputs 

12V DC Input

1.7A max current) 

Main/Aux/Solar inputs 

Interface 

Voltage/Battery Monitor 

Build in battery manager 

Dedicate Timers 

UART TX/RX 

GPIO1 and GPIO2 

1-Wire Bus Interface 

3.3V Power out 

Internal analog input scaled 

Watchdog 

Supported 

Motion Detect 

GPS/G-Sensor 

LED 

3 LED’s (Red, Green, Orange) 

Battery 

Built in battery

4400mAh Lion

 

Working Time 

> 40 hours (Continuously On) 

> 250 days Standby 

Power switch 

No 

Power Cable connector 

type 

23 pin 

Power Consumption 

< 5 Watts 

 

The JG-LS provides support for specialized hardware features through extended AT 

commands. The features supported include the following. 

 

GPS 

 

GPS location functionality is provided by the device GPS receiver. NMEA GPS 

records can be extracted in real time from the unit via the UART connection using 

special debug commands that are outside the scope of this document.   

 
GPIO 

 

Two general purpose GPIO and two additional multiplexed IO’s are presented to the 

external environment on the main connector. They are capable of providing system 

interrupts to generate a report or drive logic levels to external devices. These lines are 

3.3V logic level and are 16V tolerant. The multiplexed IO’s are typically configured as 

Ignition, Relay and Tamper. 

 
LED’s 

 

Three LED status indicators are provided to verify correct installation and operation. 

The status LEDs are color coded and directly convey the status of the cellular and 

GPS subsystems, as well as the power input; described in the table below. Their valid 

operation also indicates operational status and power. 

 

LED   

Function   

Status   

Red   

GPS   

On: 

GPS satellites acquired and locked 

Flash Slow

: GPS satellite search is in progress   

Off: 

GPS is turned off 

Содержание JG-L













Отзывы: