Spirax Sarco M10Si Automation Скачать руководство пользователя страница 8

Страница: 8 / 12

IM-P133-61

ST Issue 1

��

�

��

�

��

�

��

�

��

Temperature

Pressure bar g

Steam

saturation

curve

The product

must not

be used in this region.

A - B

2" FB and 2

" RB only

A - C ¼

" - 1

" FB, RB and 2" RB

Note:

The ﬂange standard may restrict the maximum operating pressure.

Please check with Spirax Sarco.

Body design conditions

PN100

PMA Maximum allowable pressure

70 bar g @ 40

(1 015 psi g @ 104

TMA Maximum allowable temperature

230

C @ 0 bar g

(446

F @ 0 psi g)

Minimum allowable temperature

-29

(-20

PMO

Maximum operating pressure

10 bar g

(145 psi g)

for saturated steam service

TMO Maximum operating temperature

230

C @ 0 bar g

(446

F @ 0 psi g)

Minimum operating temperature

-29

(-20

Note:

For lower operating temperatures consult Spirax Sarco



PMX Maximum differential pressure is limited to the PMO

Designed for a maximum cold hydraulic test pressure of: 105 bar g

(1 523 psi g)

2.3.2 M10Vi ball valve

Pressure psi g

Temperature

Содержание M10Si Automation













Результаты поиска

Содержание M10Si Automation

Отзывы:

Spirax Sarco M10Si Automation, Инструкция по установке и обслуживанию, Страница: 8 / 12

Результаты поиска

Содержание M10Si Automation

Отзывы: