2
3
HOW TO INSTALL BATTERIES
HOW TO CHARGE
DIRECTIONAL CONTROL
1. Press down on release button (A)
to slide down battery cover (B).
2. Install new batteries as shown in
the polarity diagram (+/-) inside
the battery compartment.
3. Replace battery door securely.
Check your local laws and
regulations for correct recycling
and/or battery disposal.
1. Turn the vehicle off.
2. Remove the cover
from the charging
cable compartment.
3. Plug the USB charging
cable into a 5V DC
computer outlet.
4. Charging LED indicates
charging. Blinking for
charging and ON when
fully charged.
HOW TO DRIVE
1. Turn on the vehicle and place on a
flat surface.
2. Press the power button and wait until
power light stops flashing.
3. You are ready to drive.
4. Use the remote control to drive.
NOTE: If your truck does not connect to the controller the first time, turn the truck off, take the batteries out of the
controller and repeat STEP 1.
HOW TO CORRECT WHEEL ALIGNMENT
TROUBLESHOOTING
A
1
2
3
For TROUBLESHOOTING questions and solutions, please visit our website:
MONSTERJAMRC.COM
NOTE: If normal function of the product is disturbed or interrupted, strong electromagnetic interference may be causing the issue. To reset product, turn it
completely off, then turn it back on. If normal operation does not resume, move the product to another location and try again. To ensure normal performance,
change the batteries, as low batteries may not allow full function.
Safety Precautions: - Keep hands, hair and loose clothing away from the motor / wheels when power switch is turned ON. - Remove batteries when not in
use. - Parental guidance is recommended for the play. - Keep your toy in your sight so that you can supervise it all the time. - New alkaline batteries are
recommended to obtain maximum performance. - Users should keep strict accordance with the instruction manual while operating the product. Note:
Parental guidance is recommended when installing or replacing batteries. Under the environment with electrostatic discharge, the toy may malfunction and
require user to reset the toy.
CARE AND MAINTENANCE: Always remove batteries from the controller when it is not being used for a long period of time. Wipe the toy gently with a clean
damp cloth. Keep the toy away from direct heat. Do not submerge the toy in water. This can damage the electronic assemblies.
REQUIRES LiFe 9.6V/700mAh battery (included) and 2 x 1.5 V AAA (LR03) batteries (not included).
Batteries or battery packs must be recycled or disposed of properly. When this product has reached the end of its useful life, it should not
be disposed of with other household waste. The Waste Electrical and Electronic Equipment Regulations require it to be separately collected
so that it can be treated using the best available recovery and recycling techniques. This will minimize the impact on the environment and
human health from soil and water contamination by any hazardous substances, decrease the resources required to make new products and
avoid using up landfill space. Please do your part by keeping this product out of the municipal waste stream! The “wheelie bin” symbol means that it should
be collected as “waste electrical and electronic equipment”. You can return an old product to your retailer when you buy a similar new one. For other options,
please contact your local council.
BATTERY SAFETY INFORMATION: Batteries are small objects. Replacement of batteries must be done by adults. Follow the polarity (+/-) diagram in the
battery compartment. Promptly remove dead batteries from the toy. Dispose of used batteries properly. Remove batteries for prolonged storage. Only
batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries
may explode or leak. DO NOT mix old and new batteries or types of batteries (i.e. alkaline/standard/rechargeable). Using rechargeable batteries is not
recommended due to possible reduced performance. Rechargeable batteries are only to be charged under adult supervision. Replaceable-rechargeable
batteries are to be removed from the toy before being charged. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
PRODUCT BATTERY REMOVAL INSTRUCTIONS: Internal battery is factory installed and non-replaceable. Product disassembly and battery removal must
be performed by an adult. Do not puncture, cut, tear, compress or deform product during disassembly. Ensure product is turned off, then use a screw driver
to remove all screws. Separate product body halves to expose internal electronics. When battery is visible in its entirety use scissors to cut a single battery
wire, immediately wrap the cut wire end with tape to isolate it, repeat until all battery wires are cut and isolated, and the battery is free from the rest of the
product. Dispose of battery in accordance with your local battery recycling or disposal laws.
FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference to radio communications. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this toy does cause interference to radio or television reception (you can check this by turning the toy
off and on while listening for the interference), one or more of the following measures may be useful:
• Reorient or relocate the receiving antenna.
• Increase the separation between the toy and the radio or the TV.
• Consult the dealer or an experienced TV-radio technician for help.
NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any transmitter component (crystal, semiconductor,
etc) could result in a violation of FCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd or they could void the user’s
authority to operate the equipment. Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221. To contact the responsible
party please visit fcc.spinmaster.com
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DO NOT CHANGE OR MODIFY ANYTHING ON THE TOY.
BEFORE FIRST USE: Read the user's information together with your child.
Spin Master Ltd., 225 King Street West, Toronto ON M5V 3M2 Canada
Imported into the EU by Spin Master International B.V., Kingsfordweg 151, 1043 GR Amsterdam, NL
Imported by Spin Master Australia Pty Ltd, Suite 101, Level 1, 18-24 Chandos Street, St Leonards, NSW 2065;
)
1800 316 982
Imported by Spin Master Toys UK Ltd. Secure Trust House, Boston Drive, Bourne End, Buckinghamshire, SL8 5YS, UK
Spin Master logo & © Spin Master Ltd. All rights reserved. Retain this information, addresses and phone numbers for future reference. Content may vary from
pictures. Keep away from obstacles and electrical hazards.
Spin Master Ltd. reserves the right to discontinue the www.MONSTERJAMRC.com website at any time.
MADE IN CHINA
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1
2
3
4
1
2
3
