A.
TOGGLE BACK to climb.
B.
C.
TOGGLE back to pull
out of dive then return to
NEUTRAL to level off.
When you are finished flying your ENTITY™, turn
the plane’s ON/OFF SWITCH to “OFF” and the
CONTROLLER’S ON/OFF SWITCH to “OFF”.
REMEMBER:
IMPORTANT INFORMATION – ADULT SUPERVISION IS RECOMMENDED
ON/OFF
Switch
Keep propellers away from face, eyes, hair, and fingers. Point plane away from face when launching. Do NOT launch at people or animals. Use caution;
make sure people around you know you are playing with Air Hogs
®
.
Recommended for use in wide-open, grassy areas. Do NOT fly near overhead
wires, trees, buildings, or other obstructions.
Do NOT fly in rain, electrical storms, snow, or other adverse weather conditions. Fly on warm sunny
days, with no wind. Do NOT fly in temperatures below 45°F/7°C. Use alkaline batteries only. Use only the charger and controller included in this package.
Please retain this information for future reference.
HOW TO COMPLETE ADVANCED STUNTS ON YOUR AIR HOGS
®
ENTITY
TM
continued
MINIMUM ALTITUDE 30 Feet (9 meters)
STEP 5 – STUNTS continued 2. SIDEWINDER
When the plane reaches a vertical position
TOGGLE – LEFT to complete a LEFT SIDEWINDER. To
complete a RIGHT SIDEWINDER, TOGGLE – RIGHT
when the plane reaches a vertical position.
In case of propeller damage, please use the steps below to replace the
damaged propeller:
1.
With one hand, grab hold of the PROPELLER.
2.
While holding the PROPELLER in place, use your opposite hand to unscrew the
removeable PROPELLER TIP with the PROPELLER REPLACEMENT TOOL.
3.
After removing the PROPELLER TIP, pull the damaged PROPELLER from the
shaft and replace with a new propeller.
4.
While holding the propeller in place, replace the PROPELLER TIP by screwing
it back onto the shaft of the PROPELLER with the PROPELLER
REPLACEMENT TOOL.
CAUTION:
The damaged propeller may have sharp edges, use caution when
handling the damaged PROPELLER, and dispose of it properly.
PROPELLER
PROPELLER TIP
PROPELLER TIP
PROPELLER
FRONT VIEW
PROPELLER
TIP
PROPELLER
TOOL
PROBLEM
SOLUTION
CAUSE
Plane will not loop.
Plane crashes
OR
will
NOT fly.
Plane not responding
to controller
OR
plane
responds to some other
signal.
1. Not enough charge.
2. STUNT FLAP is not in the
correct position.
3. Winds are too strong.
4. Improper technique.
5. Rudder Alignment is OFF.
1. Not enough charge.
2. Plane misaligned
OR
damaged
from previous flights.
1. Interference from other radio
transmission signals in the area.
1. Repeat the charging process. Refer to the “Charging your Entity
TM
”section on Page 2.
2. Adjust STUNT FLAP so that it is level with the HORIZONTAL TAIL WING.
3. Fly in conditions with little or no wind for best performance.
4 A.
LOOPING TAKES TIME AND PRACTICE!
Pilots should master directional control on their TRAINER first.
Once pilots are comfortable with their technique, they should then practice flying outdoors.
B. ENSURE: (1) the minimum altitude is reached before attempting to loop and (2) the step-by-step toggle
directions are followed (See Pages 5 and 6).
5 A. If the plane rolls out to the RIGHT before fully completing loops – Bend the rudder slightly to the LEFT.
B. If the plane rolls out to the LEFT before fully completing loops – Bend the rudder slightly to the RIGHT.
1. Repeat the charging process. Refer to the “Charging your Entity
TM
” section on Page 2.
2.
Wings:
• Use clear tape to repair wings. • Ensure that the HORIZONTAL TAIL WING is parallel to the MAIN
WING. • Ensure that the VERTICAL TAIL WING is 90° with the MAIN WING.
Propellers:
• Ensure that both PROPELLERS can spin freely.
Plane:
• Ensure plane responds to control functions by turning the plane “ON” while holding it in your hand.
1. Turn the plane “ON” and hold it in your hand.
If the plane responds without you touching the controller,
there is interference. DO NOT FLY
. You SHOULD NOT fly the plane if it does not respond to your controller,
or if it responds to something other than your controller. If the problem persists, it is recommended that you
fly your plane in another area.
CHANGING PROPELLERS ON YOUR ENTITY™
FCC REQUIREMENTS
TROUBLESHOOTING GUIDE
CAUTION: Changes or modifications to this product not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada
Spin Master, Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221
Spin Master Toys Far East Limited, Rm # 1113, 11/F, Chinachem Golden Plaza, 77 Mody Rd.,
Tsimshatsui E., Kowloon, HK
North American Consumer Information
Phone: 1-800-622-8339
www.spinmaster.com
Air Hogs ® is a registered trademark and Entity TM is a trademark of Spin Master Ltd.
© 2006 Spin Master Ltd. All rights reserved. Manufactured for and
distributed by Spin Master Ltd. Conforms to safety standards ASTM F963-03,
EN71 Regulatory Requirements. Products and colors may vary.
Please retain this information for future reference. MADE IN CHINA.
Asst. #44288, #20006996, #20006997
REV 1 US ENG
44288-ENG-IS-R1(1)
TM
Contains NiMH battery pack.
Battery pack must be recycled
or disposed
of properly.