STEP 1
STEP 3
STEP 5
STEP 2
STEP 4
Ensure that the ON/OFF
SWITCH on the plane and the
charger are “OFF”.
Insert the
CHARGE NOZZLE
into the plane’s
CHARGING PORT.
Start charging by switching the charger’s ON/OFF
SWITCH to “ON”. Let the plane charge for 5 minutes.
NOTE: The CHARGING LIGHT on the charger will
blink red during charging. When charging is
complete, the READY LIGHT will turn to a solid green.
If the ready light and charging light blink at the
same time, the charger’s batteries must be replaced.
ON/OFF
Switch
ON/OFF
Switch
Charging
Port
Charge Nozzle
Turn the ON/OFF SWITCH
on charger to “OFF”.
Unplug the CHARGE NOZZLE from the
plane’s CHARGING PORT.
NOTE: You are now ready to set up your
Entity™ for indoor training.
PLANE
CHARGER
Ready Light
Charging Light
IMPORTANT: BEFORE YOUR FIRST FLIGHT, YOU MUST CHARGE AND DISCHARGE YOUR AIRPLANE FULLY 1 TIME. YOU MUST ALSO REPEAT
THIS STEP WHEN A PROLONGED PERIOD OF TIME HAS PASSED WITHOUT FLYING. FAILURE TO DO THIS WILL RESULT IN SHORTENED
LIFESPAN FOR YOUR AIRPLANE. FOR ALL OTHER FLIGHTS, CHARGE THE BATTERIES ONCE ONLY. DO NOT OVERCHARGE THE BATTERIES AS
THIS WILL PERMANENTLY DAMAGE THE BATTERIES.
CONTROLLER
CHARGER/TRAINER/DISPLAY STAND
• Battery installation should be performed by an adult. • Use only batteries recommended. Be careful to install the batteries with the correct polarity, as
indicated. • Do NOT mix old and new batteries. • Do NOT mix alkaline, standard, or rechargeable batteries. • Do NOT attempt to charge non-rechargeable
batteries. • Do NOT short circuit the supply terminals. • Do NOT overcharge the plane’s batteries. • Exhausted batteries are to be removed, as they will
adversely affect the performance. • Do not dispose of batteries in fire. Battery may explode or leak. • CAUTION: Plane contains a rechargeable cell. If fluid
leaks from the plane, avoid contact with eyes and dispose of the plane. Only use charger supplied with this package. • Do NOT use any other source to
charge your Entity
TM
. • Different types of batteries or new and used batteries are not to be mixed. • Do not use rechargeable batteries. • Only batteries of the
same or equivalent type as recommended are to be used. • Rechargeable batteries are to be removed from the toy before being charged
(if removable). • Rechargeable batteries are only to be charged under adult supervision (if removable).
Contents:
1 Entity™ Stunt Plane
1 Controller
1 Charger/Trainer/Display Stand
2 Extra Propellers
1 Tool
1.
Use a Phillips screwdriver to loosen the screw
in the battery compartment door.
2.
Remove the battery door.
3.
Insert six
1.5 Volt AA batteries
(not included).
4.
Replace battery compartment door and
refasten the screw.
IMPORTANT:
Be sure to insert the batteries as indicated inside
compartment with the correct polarity.
1.
Use a Phillips screwdriver to loosen the screw in the
battery compartment door.
2.
Remove the battery door.
3.
Insert eight 1.5 Volt D alkaline batteries (not included).
4.
Replace battery compartment door and refasten
the screw.
IMPORTANT:
Be sure to insert the batteries as indicated inside
compartment with the correct polarity.
®
INSTRUCTIONS
NO ASSEMBLY REQUIRED
BATTERY INSTALLATION
IMPORTANT BATTERY INFORMATION
CHARGING YOUR ENTITY
TM
Stunt Flap
Adjustment
Knob
Stunt Flap
Vertical
Tail Wing
Rudder
Antenna
Horizontal
Tail Wing
Plane Body
Main Wing
Propeller
Propeller Tip
ON/OFF
Switch
Charging
Port
Propeller
Propeller Tip
Charging
Indicator
Light
ON/OFF
Switch
Toggle
Thrust
Button
Land
Button
CONTROLLER
ENTITY™ STUNT PLANE
CHARGER/TRAINER/DISPLAY
STAND
Tool
Ready
Light
Charging
Light
ON/OFF
Switch
Charging
Hose
Charge
Nozzle
Charger
Base
Training
Stand
TM