manualshive.com logo in svg

spikenzielabs Solder:Time 495, Быстрый старт

Поделиться
Скачать
spikenzielabs Solder:Time 495 Скачать руководство пользователя страница 8

1.

 

•

Soldering iron 

2.

 

•

Solder 

3.

 

•

Flush cutters 

Hint: 

1.

 

When trimming the leads for this kit, trim them as close to the PCB as possible. This will make it easier to assemble the plastic watch 
parts when building the watch body. 

 

Solder : Time™ watch with wrist strap. 

Solder : Time™ schematic. 

Legal: 

 

License:  

The Solder : Time design, a time piece made of layered plastics, it’s schematic and source code / firmware are presented here strictly for 
educational and informative purposes. SpikenzieLabs retains all rights to the design, look, source code and firmware. Reproduction is allowed 
only for personal use. No commercial reproduction is allowed without previous written approval from SpikenzeLabs. 

 

Trademark: 

Solder : Time is a trademark of SpikenzieLabs. 

Source Code: 

 

Assembly File:  

Here is the source code for the Solder : Time™ written in assembly. Use Microchips’ 

MPLAB

 to modify the code and recompile new HEX files 

to reprogram the Solder : Time™. 

 

Assembly: 

Watch.asm.zip

 

 

HEX file:  

Here is the compiled standard release version of the HEX code for the Solder : Time™. A good choice to program the Solder : Time™ is using 
Microchips’ 

PicKit

 programmers. 

Содержание Solder:Time 495










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды