Sphere U6DNC Series Скачать руководство пользователя страница 11

Страница: 11 / 22

R107

2.2K ¼ W Resistor 5%

Axial leads. CC: red, red, red, gold

R-Ground

1 Megohm ¼ W Resistor 5%

Used to provide a static drain to a metal
cabinet.

Optional

Q1, Q2

MPSA42 Transistor

Align to case outline on PCB.

Q100

IRF820 or sim. MOSFET

Caution, static sensitive, handle with care.
Attach to board with provided screw and nut,
place head on underside to avoid track short.

Q101

2N2222A or PN2222 Transistor

Board accepts either type, note that flat line is
on the wrong side on early board artwork,
emitter goes to the outside track.

S1, S2, S3

Pushbutton switches

Can also be external switches of any kind,
SPST, Normally Open.

UP1

Programmed Atmel Microcontroller

Install in socket, as last operation to avoid
static damage. Check alignment.

U1, U2, U3, U4,
U5, U6

74141 or K155ID1 Nixie Driver

Install in 16 pin sockets, nixie drivers.

Maxim DS32KHZ
32.768KHz TCXO, DIP

Optional

stabilized TCXO, DIP package

Maxim DS32KHZ
32.768KHz TCXO, SMD

Optional

stabilized TCXO, SMD package

LM340T5, 7805CT or sim. 5V
Regulator

Attach to board with mounting hardware.

U10

LM340T12, 7812CT, or sim. 12V
Regulator

Used only if raw input power is higher than
12VDC.

Optional Jumper input to output

pads if not used.

U100

NE555T, LM555N etc., timer

Use 8 pin dip socket underneath.

32.768KHz Crystal, may have the
frequency or a code like R38 on it.

Radial Leads. Default timebase.

16 Pin Sockets

6 pieces, under each driver, U1-U6

8 Pin Socket

1 piece under U100

40 Pin Sockets

1 piece, under microprocessor UP1

Threaded Spacers
and mating screws

5 pieces, mount under the board with
provided screws.

4-40 tapped, can be used to attach the board
to your own case design.

Screws and nuts

For U9 and Q100

4-40 or 3mm.

Angle brackets &
screws

For the provided remote switch
assembly

4-40 screws and brackets

Ribbon Wire

4-wire For remote switch assembly.

1 foot. Can be gray or colored.

Solder

Water soluble

rosin core solder,

as requested. Relevant type is
CIRCLED.

63-37 formula, for minimal cold solder joints.

Содержание U6DNC Series




















Результаты поиска

Содержание U6DNC Series

Отзывы:

Похожие инструкции для U6DNC Series

Бренды по названию

Популярные бренды

Sphere U6DNC Series, Руководство пользователя

Результаты поиска

Содержание U6DNC Series

Отзывы:

Похожие инструкции для U6DNC Series

Бренды по названию

Популярные бренды