background image

7

6.0 FUSE REPLACEMENT

 

WARNING

  To avoid personal injury or damage to the Meter, use specified fuses ONLY in accordance with the following 

procedure.

TO REPLACE THE METER’S FUSE:
1.   Turn the Meter off and remove test leads from the input terminals.
2. Remove the rubber boot from the Meter.
3. Remove the 3 screws from the case bottom, and separate the case top from the case bottom.
4. Remove the fuse by gently prying one end loose, then remove the fuse from its bracket.
5.  ONLY install replacement fuses of the identical type and specification as follows and make sure that all fuses are 

inserted firmly into the fuse holder brackets.

Fuse 1: 10A, 250V, fast type, 5x20 mm.

6.  Rejoin the case bottom and case top, and reinstall the 3 screws.  Be carefull not to overtighten the screws. Reinstall 

the rubber boot. 
Replacement of the fuses is seldom required. A burned fuse suggests improper operating procedures.

A. GENERAL SERVICE 
•  Periodically wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents.
•  To clean the terminals use a cotton swab and detergent, as dirt and moisture in the terminals can affect readings.
• Turn the Meter power off when it is not in use.
• Take out the battery when it is not used for a long time.
• Do not use or store the Meter in a place of humidity, high temperature.

SPERRY INSTRUMENTS LIMITED LIFETIME WARRANTY

Subject to the exclusions and limitations detailed below, Sperry Instruments provides a limited lifetime warranty on products  

of its manufacture will be free from defects in materials and workmanship under normal use and service.

Limited

Limited means that Sperry Instruments warrants to the original purchasers of products from Sperry Instruments authorized distributors at the time of 

shipment such products shall be free of defects in material and workmanship while the tool is used under normal working conditions. Standard wear 

and tear, dulling over time, overloading, misuse, and acts of God are not covered under warranty. This warranty does not cover batteries, fuses, or test 

leads.

When a warranty claim arises, the purchaser must contact Sperry Instruments. If the defect comes under the terms of this  

limited warranty, Sperry Instruments will arrange, at its sole discretion, one of the following options: 

• Product will be replaced

The purchaser is solely responsible for determining the suitability of Sperry products for the purchaser’s use or resale, or for incorporating them into 

articles or using them in the purchaser’s applications. The distributor is authorized to extend the foregoing limited warranty to its original purchasers in 

connection with the sales of Sperry products, provided that such products shall not have been altered by the distributor. The distributor shall be fully 

responsible for any warranties the distributor makes to its purchasers which are broader or more extensive than Sperry’s limited warranty. 

Lifetime Warranty

Warranty Limitation: The forgoing warranties are exclusive and are in lieu of all other express and implied warranties whatsoever, including but 

not limited to implied warranties of merchantability and fitness for a particular purpose. The foregoing warranties do not cover ordinary wear and 

tear, abuse, misuse, overloading, alterations, products which have not been installed, operated or maintained in accordance with Sperry’s written 

instructions. Test leads, fuses, batteries and calibration are not covered under any implied warranty. “Lifetime” of products that are no longer offered 

by Sperry will be either repaired or replaced with an item of Sperry Instruments choice of similar value. Lifetime is defined as 5 years after Sperry 

discontinued manufacturing the product, but the warranty period shall be at least ten years from date of purchase. Original proof of purchase is 

required to establish original ownership of product.

No warranty will be honored unless an invoice or other proof of purchase date is provided to Sperry Instruments. Hand written receipts or invoices will 

not be honored. 

©2016 Product Power, LLC All rights reserved.

- See more at: http://www.sperryinstruments.com/en/resources/warranty-page#sthash.4sNKZu3b.dpuf

Sperry Instruments
800-645-5398
Menomonee Falls, WI 53051
sperryinstruments.com

SPR_TL_068_0916

Содержание DM6450








Отзывы: