PAGE 1 OF 2
S P E L L M A N H I G H V O LTA G E E L E C T R O N I C S C O R P O R A T I O N
Spellman’s Bertan brand of 230 Series high voltage power
supplies provide regulated high voltage outputs from 1 to
30kV. The low noise, linear topology employed results in
extremely low output ripple specifications. These 12 to 15
watt units are inherently reversible by design, providing
either positive or negative output polarity. The 230 Series is
fully arc and short circuit protected. Excellent regulation
specifications are featured along with outstanding stability
performance.
TYPICAL APPLICATIONS
HiPot Testing
Electrostatics
General Laboratory Usage
SPECIFICATIONS
Input Voltage:
115Vac, ±10%, 50/60 Hertz @ 0.5 amp
230Vac, ±10%, 50/60 Hertz @ 0.25 amps
Input voltage is switch selectable
Output Voltage:
See “model selection” table
Output Polarity:
All units are reversible polarity by design
Output Current:
See “model selection” table
Voltage Regulation:
Line:
≤
0.002% of rated output voltage over specified
input voltage range
Load:
≤
0.005% of rated output voltage for a full load
change
Current Regulation:
Internally set to limit at less than 125% of rated current.
A rear panel switch allows limiting at 25% of rated full current.
Ripple:
See “model selection” table
Temperature Coefficient:
≤
100ppm/°C
Stability:
≤
0.01%/hour, 0.02% per 8 hours after a 1/2 hour warm up
Accuracy:
Front panel control: ±(0.2% of s 0.2% of maximum)
Front panel Meter: Voltage ±(0.5% of s 0.5% of
maximum), Current ±(2% of s 0.5% of maximum)
Remote Programming: ±(0.1% of s 0.1% of maximum)
Voltage Monitor: ±(0.1% of r 0.1% of maximum)
Current Monitor: ±(2% of r 1% of maximum)
Front Panel Metering and Controls:
Power ON/OFF switch
3.5 digit metering for voltage and current, switch selectable
Polarity indicator
10 turn locking potentiometer to set output voltage
HV output connector
Ground stud
Operating Temperature
0°C to +50°C
Storage Temperature:
-40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Input Line Connector:
IEC320 EMI filter/input connector, a detachable
line cord is provided
Interface Connector:
9 pin “D” connector, a mating connector is provided
Output Connector:
A detachable 10 foot (3 meter) HV cable is provided
for units up to 5kV; 10kV through 20kV: 59” (1.5 meter);
30kV: 10 foot (3 meter)
Cooling:
Convection cooled
Dimensions
7.63˝ W X 5.03˝ H X 8.91˝ D
(194mm X 128mm X 226mm)
Weight:
≤
10 pounds (4.5kg)
Regulatory Approvals:
Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive.
230
HIGH VOLTAGE
POWER SUPPLY
•
MODULAR BENCH TOP DESIGN
•
LOW RIPPLE AND NOISE
•
3.5 DIGIT FRONT PANEL DIGITAL METERING
•
REVERSIBLE OUTPUT POLARITY
USA
+1-631-630-3000
FAX: +1-631-435-1620
UK
+44 (0)1798 877000
FAX: +44 (0)1798 872479
JAPAN
+81 (0)48-447-6500
FAX: +81 (0)48-447-6501
CHINA
+86 (0)512-67630010
FAX: +86 (0)512-67630030
e-mail: [email protected]
www.spellmanhv.com
128051-001
REV.D
Spellman High Voltage is an ISO 9001:2000 and ISO 14001:2004 registered company
www.spellmanhv.com/manuals/230
