Spektrum AR637T Скачать руководство пользователя страница 7

Страница: 7 / 27

Initial Setup

Verify your transmitter is updated to the latest Spektrum AirWare™ software

to take advantage of Forward Programming. See your transmitter manual

for updating instructions.

Install the receiver in your airplane.

Bind the receiver to your transmitter.

Complete the airplane setup on your transmitter including wing type, tail type, channel

assignments, mixing, sub trim and travel the same as you would for any other aircraft

without AS3X. Verify the center of gravity is correct and test fly your aircraft.

IMPORTANT:

Do not use open mixes for flight control surfaces when setting

up a model with the AR637T for AS3X and SAFE. Only use wing and tail type

options to configure flight controls, refer to your transmitter manual for more

information about wing and tail type features.

their last position. When the receiver detects the signal from the transmitter,

normal aircraft operation resumes.

Preset Failsafe

With preset failsafe, you can set the specific control surface positions you

want to use if the signal is lost. When the receiver detects the signal from the

transmitter, normal aircraft operation resumes.

Preset failsafe mode is only available through Forward Programming.

SAFE Failsafe

SAFE Failsafe mode will work to automatically level your aircraft if the signal is

lost. In the forward programming menu you can select the bank and pitch an-

gles the aircraft will attempt to maintain during failsafe. We recommend setting

bank and pitch angles so the aircraft flies a gentle gliding turn, preventing a fly-

away. You must complete

First Time SAFE Setup

before this option is available.

SAFE Failsafe mode is only available through Forward Programming.

Testing Failsafe

Secure the aircraft on the ground and remove the propeller. Test Failsafe

settings by turning the transmitter RF output off and noting how the receiver

drives the control surfaces.

Receiver Power Only

• The servo ports will not have a control signal if the receiver is turned on

when no transmitter signal is present.

• All channels have no output until the receiver has linked to the transmitter.

Please see the following link for a detailed video series.

https://youtube.com/playlist?list=PL3xicOtuJ600AEzU-

jw7Q03tC4aRD-8T-2

Содержание AR637T




























Результаты поиска

Содержание AR637T

Отзывы:

Похожие инструкции для AR637T

Бренды по названию

Популярные бренды

Spektrum AR637T, Руководство пользователя

Результаты поиска

Содержание AR637T

Отзывы:

Похожие инструкции для AR637T

Бренды по названию

Популярные бренды