background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

7

512063

In mobile home installations, dryer exhaust duct 

must be secured to mobile home structure.

Dryer exhaust duct MUST NOT terminate under 

mobile home.

Dryer exhausts 220 cfm (measured at back of 

dryer).

Static pressure in exhaust duct should not be 

greater than .6 inches water column (1.5 cm), 

measured with manometer placed on exhaust 

duct two feet (61 cm) from dryer (check with 

dryer running and no load).

Exhausting dryer in hard-to-reach locations can 

be done by installing 521P3 Flexible Metal Vent 

Kit (available as optional equipment at extra 

cost).

Failure to exhaust dryer properly will void 
warranty.

NOTE: Venting materials are not supplied with the 
dryer (obtain locally).

Exhaust Direction

The dryer can be exhausted to the outdoors through the 

back, left, right or bottom of the dryer. 

EXCEPTION: 

Gas dryers cannot be vented out the left side 
because of the burner housing.

Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be 

accomplished by installing a Directional Exhaust Kit, 

528P3, available as optional equipment at extra cost. 

Exhaust System

For best drying results, recommended maximum 

length of exhaust system is shown in 

Table 1

.

To prevent backdraft when dryer is not in operation, 

outer end of exhaust pipe must have a weather hood 

with hinged dampers (obtain locally).

NOTE:  Weather hood should be installed at least 
12 inches (30.5 cm) above the ground. Larger 
clearances may be necessary for installations where 
heavy snowfall can occur.

Table 1 

Number of 

90° Elbows

Weather Hood Type

Recommended

Use Only for Short Run installations

Maximum length of 4 in. (10.2 cm) diameter rigid metal duct.

0

65 feet (19.8 m)

55 feet (16.8 m)

1

55 feet (16.8 m)

47 feet (14.3 m)

2

47 feet (14.3 m)

41 feet (12.5 m)

3

36 feet (11.0 m)

30 feet (9.1 m)

4

28 feet (8.5 m)

22 feet (6.7 m)

Maximum length of 4 in. (10.2 cm) diameter flexible metal duct.

0

45 feet (13.7 m)

35 feet (10.7 m)

1

35 feet (10.7 m)

27 feet (8.2 m)

2

30 feet (9.1 m)

21 feet (6.4 m)

3

25 feet (7.6 m)

17 feet (5.2 m)

4

20 feet (6.1 m)

15 feet (4.5 m)

NOTE: Deduct 6 feet (1.8 m) for each additional elbow.

4 in.

(10.2 cm)

4 in.

(10.2 cm)

D673I

D802I

2-1/2 in.

(6.35 cm)

Содержание KES18AWF

















Отзывы: