Spectrum Techniques ICS-PCI Скачать руководство пользователя страница 31

Страница: 31 / 43

Temp Correction...

The optional temperature correction feature allows for correcting peak shifts that occur as the temperature changes affect

the detector. A special tube base containing a compatible temperature sensor is required. In no such sensor is detected at

startup, the Temperature Correction menu is not displayed.

Presets...

Click on the desired preset condition and enter the number, click on OK to enter data and exit menu.

Amp/HV...

Enter the detector manufacturer's recommended high voltage value, click on On/Off to desired position. Set Course and

Fine Gain by either entering number or by moving sliding scale. Click on desire Conversion Gain. Set LLD and ULD by

either entering number or by moving sliding scale. When all setting are entered click on OK, this will set the adjustments

and exit menu to spectrum screen.

Содержание ICS-PCI












































Результаты поиска

Содержание ICS-PCI

Отзывы:

Похожие инструкции для ICS-PCI

Бренды по названию

Популярные бренды

Spectrum Techniques ICS-PCI, Руководство пользователя

Результаты поиска

Содержание ICS-PCI

Отзывы:

Похожие инструкции для ICS-PCI

Бренды по названию

Популярные бренды