Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 93

Страница: 93 / 109

Page F-4

LiQuilaz II E and S Operations Manual

Appendix F Serial Communications Overview

Connector Signals

Table

F-1

shows the standard PC serial port connection. The highlighted signals (RX,

TX and Ground) are required signals for Particle Measuring System instruments. The
signals shown in italics are not used.

Table

F-1

Standard PC Serial Port (DB-9)

Pin

In/Out

Description

DCD (Data Carrier Detect)

RX (Receive)

Out

TX (Transmit)

Out

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

Out

RTS (Request to Send)

CTS (Clear to Send)

RI (Ring Indicator)

Table

F-2

shows the RJ-12 connector pinout for many Particle Measuring Systems

instruments. Pins shown as

instrument dependent

are not usually available. On some

instruments, the pins may be tied together to simulate hardware flow control. On
other instruments, the pins are not used at all. See instrument-specific documentation
to verify the details.

An adaptor cable is provided with instruments that use this interface. Order P/N PMS-
CD1995.

Table

F-2

RJ-12 Instrument Connector

Pin

In/Out

Description

DSR (instrument dependent)

Out

TX (Transmit)

RX (Receive)

Out

RTS (instrument dependent)

CTS (instrument dependent)

Ground

Содержание Particle Measuring Systems LiQuilaz II E














































































































Результаты поиска

Содержание Particle Measuring Systems LiQuilaz II E

Отзывы:

Бренды по названию

Популярные бренды

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Результаты поиска

Содержание Particle Measuring Systems LiQuilaz II E

Отзывы:

Бренды по названию

Популярные бренды