SpectraPure MarinePRO RO System Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 24

SpectraPure MarinePRO RO System Скачать руководство пользователя страница 21

SpectraPure®Inc

.

Fax 480.894.6109 Fax us toll-free 1.877.527.7873

E-mail: [email protected] Visit us on the web www.spectrapure.com

21

SpectraPure

®

Product Water - Low Production Rate

Cause

Corrective

Action

Plugged pre-filters

Replace pre-filters

Low water temperature

Heat feed water or use higher GPD membrane

Low feed pressure

Use booster pump or use higher GPD membrane

Fouled membrane

Replace membrane

Membrane Troubleshooting Guide

The following chart illustrates the procedure for determination of RO membrane
performance. However, the chart represents only rough guidelines for determin-
ing performance of RO membrane. Depending on your tap water chemistry, the
rejection characteristics of the membrane may vary significantly.

Method of Calculate %

Test Results

Conclusion

Testing

Rejection

TDS/

Measure feed water and Is Rejection

No - Replace Membrane

Conductivity RO product water TDS/

greater than

Yes - Membrane OK

Tester Conductivity

95%

?

Alkalinity

Measure feed water and Is Rejection

No - Replace Membrane

Test Kit

RO product water

greater than

Yes - Membrane OK

Alkalinity 90%

?

Hardness

*Measure feed water

Is Rejection

No - Replace Membrane

Test Kit

and RO product water

greater than

Yes - Membrane OK

Hardness 90%?

*Caution: This test is not to be used on softened water sources.

Please feel free to contact us here at the factory for

any technical questions or problems you may have.

Toll-Free 1-800-685-2783

TROUBLESHOOTING GUIDE:

«
...
19
20
21
22
23
...
»

Содержание MarinePRO RO System

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды