manualshive.com logo in svg

SpectraPure LLC-UPLC-ATO, Руководство по установке

Поделиться
Скачать
SpectraPure LLC-UPLC-ATO Скачать руководство пользователя страница 3

SpectraPure

®

Inc

. 

 Fax  480.894.6109 Fax us toll-free 1.877.527.7873

[email protected]                       www.spectrapure.com

3

SpectraPure

®

SpectraPure

® 

Inc

. assumes no responsibility for water damage due 

to leaks or misapplications of our products. It is the user’s responsibility 

to determine that the system is leak-free and properly installed.

SYSTEM FEATURES                                                                                        

•  Highest Quality and Accuracy -- New and Improved “Gen 6” 

 

LiterMeter3 Pump machined to aerospace tolerances. Antiwear and anti-

friction coated for exceptional pump life.

•  Fully automatic operation - May be programmed to fill a vessel or to 

drain a sump (Fill Mode/Drain Mode).

•  High reliability metal pump housing
•  Virtually maintenance free
•  No damage to the pump if run dry
•  No check valves to clog or seals to leak
•  Self-priming and anti-siphoning
•  High limit Sensor Tube for fail-safe operation
•  High delivery pressure - over 40 psi
•  Compact size and cool operation
•  Kalkwasser safe
•  Quiet operation and low power consumption
•  Complete system consumes less than 3 watts when pump is on
•  Extended 

5-year Warranty

SYSTEM SPECIFICATIONS:                                                                                  

Pump Flow Rate:

  Adjustable in 10 Steps up to 180 ml./min.

Dimensions:

  5.35"L x 2.15"H x 2.2"W (13.6 cm. x 5.5 cm. x 5.6 cm.)

Maximum Daily Total (per Pump):

  260 liters (68.5 gals.)

Draw Height:

  from maximum 

25 feet

 (7.6 meters) below

Delivery Height:

  to maximum 

60 feet

 

(18.3 meters) above

Power Supply: 

115VAC /12VDC wall-mounted power supply

(Can be powered by 12VDC battery)

Содержание LLC-UPLC-ATO

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды