manualshive.com logo in svg

SpectraPure Coffee Lovers System CLS-5-90, Руководство по эксплуатации

Поделиться
Скачать
SpectraPure Coffee Lovers System CLS-5-90 Скачать руководство пользователя страница 2

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

2

Copyright © 2009 by SpectraPure Inc.

ALL RIGHTS RESERVED

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any 

form or by any means, electronic, mechanical, photocopying, recording or otherwise without 

the prior written permission of SpectraPure Inc.

TABLE OF CONTENTS

Operational Specifications

     System Description ..........................................................................................................................................................................  3
     RO Feed Water Requirements .....................................................................................................................................................  4

Preparation

     Drill Hole for Faucet in a Porcelain Sink ...................................................................................................................................  5
     Punch Hole for Faucet in Stainless Steel Sink .........................................................................................................................  5

Feed Supply Valve Installation

.................................................................................................................................................  6

Procedure for Measuring Waste to Product Water Ratio

 .........................................................................................  7

     Flow Restrictor Removal, Adjustment, and Replacement...................................................................................................  8
     Flow Ratio Chart ..............................................................................................................................................................................  9

Faucet Installation

     Air-Gap Faucet Installation ..........................................................................................................................................................  10

Drain Saddle Installation

 ............................................................................................................................................................  11

Tank Installation

     Installing Ball Valve on Tank .......................................................................................................................................................  12
     Tank Install ........................................................................................................................................................................................  12

Ice Maker Hook-up (optional)

 ..................................................................................................................................................  12

Mounting System

     Mounting Installation ....................................................................................................................................................................  13
     Start-up Procedures ........................................................................................................................................................................  13

Maintenance Procedures

     System Schematic ...........................................................................................................................................................................  14
     Procedures and RO Membrane Replacement .......................................................................................................................  15
     Recharging the Bladder Tank .....................................................................................................................................................  16
     Sanitizing System ............................................................................................................................................................................  17

Troubleshooting Guide

................................................................................................................................................................  18-22

Warranty Information

 ..................................................................................................................................................................  23

     Replacement Parts ..........................................................................................................................................................................  24

Thank You for your purchase of a 

SpectraPure® System. With proper installation and maintenance, this system will 

provide you with high quality water for years to come. All  SpectraPure®  products are rigorously tested by  us for 
safety and reliability. If you have any questions or concerns, please contact our customer service department at 
1.800.685.2783 or refer to our online troubleshooting at www.spectrapure.com.

Содержание Coffee Lovers System CLS-5-90

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды