manualshive.com logo in svg

Spectral Instruments Series 800, Руководство пользователя

Поделиться
Скачать
Spectral Instruments Series 800 Скачать руководство пользователя страница 41

5.  Camera System Warranty And Service 

 
The S800 camera is warranted for 12 months after shipment.  Any failure that occurs 
within that period, that is not due to mishandling or operating the camera under 
conditions that void the warranty, is repaired at no charge to you. 

5.1   The Warranty Conditions 

The camera is guaranteed against failure of any component and against failure 
due to manufacturing processes for the warranty period. 
 
Operation of the camera under environmental conditions that are outside of the 
operating specifications voids the warranty. 
 
The camera system is not warranted against damage from mishandling or for 
damage that occurs from natural or man-caused conditions such as flood, fire, 
wind, lightning etc. 

5.2   Returning A Camera For Service 

A S800 camera can only be serviced at the factory.  You must obtain a Return 
Material Authorization number from Spectral Instruments customer service 
department before any camera component is returned for service.  

5.3   Diagnosing A Camera Problem 

There are no user serviceable components in the camera head or the power 
supply unit and it is highly likely that the user could exacerbate a problem by 
attempting to “open something up.”  Spectral cameras are assembled in an anti-
static clean room to insure the safety of the CCD and the cleanliness of the 
camera interior.  Section 8., troubleshooting, describes in detail how to perform 
the diagnostic tests that are permitted.  The result of such tests is primarily to 
distinguish between a cable problem (bad connection or broken cable), a camera 
problem and an application problem. 

5.3.1 No 

Response 

The PDCI card must be correctly seated.  It is possible to have the software 
indicate that the card has been successfully initialized and still have the SI Image 
application fail to run.  Most frequently this is an interrupt conflict or failure to 
get an interrupt service connection properly set up.  Try reseating the PDCI card 
and maybe move it to an adjoining slot.  There has been some indication of an 
odd vs even slot interrupt assignment that has occasionally caused the SI Image 
program to fail to run. 

5.3.2 Fuses 

If the camera does not turn on when plugged into the appropriate mains power a 
fuse could be the problem.  If this is a first-time turn-on for the camera system 
and it fails to power up, check that the power setting indicated on the power entry 

Содержание Series 800







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды