Spectra Precision QuickMark Layout QML800 Скачать руководство пользователя страница 40

Страница: 40 / 44

Calibration

Accuracy

The “Set Up Verification” function that follows job set up is the best way to verify system accuracy.

Open a job (new or existing), be very careful with benchmarks and then follow the steps for “Set Up

Verification.” If the measured and calculated distances are the same, the unit is within calibration.

Repeatability

To check repeatability, create several points and mark them on the floor. Return to those points. If the

system returns to the same point, within 1/16” (1.5mm), the system is within calibration.

Plumb

Drive to a point where the “X” can be seen on both the floor and ceiling. Use the included LP30 plumb

pointer to verify that the “X” on the ceiling is direct plumb with the point on the floor.

Calibration and Service

Service

There are no maintenance service requirements

Содержание QuickMark Layout QML800













































Результаты поиска

Содержание QuickMark Layout QML800

Отзывы:

Похожие инструкции для QuickMark Layout QML800

Бренды по названию

Популярные бренды

Spectra Precision QuickMark Layout QML800, Руководство пользователя

Результаты поиска

Содержание QuickMark Layout QML800

Отзывы:

Похожие инструкции для QuickMark Layout QML800

Бренды по названию

Популярные бренды