background image

Spectra 64K Library Stability Kit Installation Procedure

2

Notices

Spectra Logic Corporation provides the unit “as is” without warranty of any kind, either 
expressed or implied, including but not limited to the implied warranties of merchantability or 
fitness for a particular purpose. In no event shall Spectra Logic be liable for any loss of profits, 
loss of business, loss of use or data, interruption of business, or for indirect, special, incidental, 
or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of 
such damages arising from any defect or error.

Information furnished in this manual is believed to be accurate and reliable. However, no responsibility 
is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may 
revise this publication from time to time without notice, and reserves the right to change any product 
specification at any time without notice.

Spectra 64K Library Stability Kit Installation Procedure
Copyright © 2004 Spectra Logic Corporation. All rights reserved.

Spectra Logic Contact Information

 

 

Corporate Headquarters

European Office

Address

Phone

Fax

Spectra Logic Corporation 
1700 N 55th Street 
Boulder CO 80301
USA 

(800) 833-1132 or (303) 449-6400

(303) 939-8844

Address

Phone

Fax

Spectra Logic Europe Limited
Magdalen Centre
Robert Robinson Avenue
Oxford Science Park
Oxford
UK OX44 7 RW

+44 (0) 870 112 2150

+44 (0) 870 112 2175

Web Site

http://www.SpectraLogic.com

Содержание Spectra 64K













Отзывы: