Spearhead 8999071 Скачать руководство пользователя

Страница: 24 / 32

8999071EN: v1.410/10/2019

Original instructions (ENGLISH)

Website: www.spearheadmachinery.com

Troubleshooting

Trouble

Causes

Remedies

Irregular Cut

Worn, bent or broken flails

Replace the flails

Too low RPM

Increase RPM

Machine is not in the level with the
ground

Correct mounting on the tractor

Clogged material due to excessive
working speed

Reduce the working speed

Noise

Loosen bolts

Tighten the bolts

Damaged parts of the machine

Find damages and repair the
machine

Noise In The Gearbox

Lack of oil

Fill till level

Worn gears

Replace

Worn bearings

Replace

Vibrations

Broken or worn flails

Replace

Unbalanced rotor

Balance or replace

Worn rotor bearings

Replace

Excessive Backlash In Joints

Worn pins

Replace

Damaged Bearings

Dirty or ungreased bearings

Clean and grease

Violent impact on the ground when
the machine is lowered

Lower it gently

Belts Overheating

Belts slipping

Tension the belts

Working flails are touching the
ground

Adjust the height of cut

Too fast working speed

Reduce the speed

Содержание 8999071

































Результаты поиска

Содержание 8999071

Отзывы:

Похожие инструкции для 8999071

Бренды по названию

Популярные бренды

Spearhead 8999071, Руководство и каталог запчастей

Результаты поиска

Содержание 8999071

Отзывы:

Похожие инструкции для 8999071

Бренды по названию

Популярные бренды