TIME Series Controller
Page 10
1
. Pressing Zone 1-4 chooses the speakers in that zone and
allows presets, on/off to work on those speakers
2.
Pressing Speaker Selector + button sends control to the
next speaker that can be controlled in that zone in a clock-
wise order. Pressing Speaker Selector - button sends control
to the next speaker that can be controlled in that zone in
a counter clockwise order. The LED on the loudspeaker se-
lected should light on the on the unit (the light on the remote
is not synchronized to the speaker being selected it is only a
visual indication that you have moved to the next speaker).
3.
To control the movement of a speaker in the room, af-
ter selecting the loudspeaker you want to control, press the
Control button and the light on the speaker selected should
begin flashing.
4.
After selecting the speaker for control, turning the Dial on
the remote to the right or left causes the speaker to rotate
to the desired location. The LED on the speaker is at a point
considered the “pointing direction.” So line up the LED where
you want the speaker to point.
5.
While the speaker is selected for control, use the Preset Tilt
Angles to lower the loudspeaker into the room. Depending
on the height of the room and the desired prime listening
area, determines the proper angle to use. Choose 0º, 15º,
30º, or 45º to angle the loudspeaker to the desired location.
6.
When you are done controlling that loudspeaker, press the
Control button and the LED on the loudspeaker should stop
flashing and be lit all the time.
7.
Return to step 2 for the next speaker you want to control
and repeat steps 4 and 5 until all speakers in the zone are
aimed the way you want them to be.
8.
To store the preset for the new speaker locations in that
zone after you set all the speakers in that zone and while you
are still in the control mode, press and hold the store button,
until all LED’s on remote flash, indicating that you are in the
Store mode. Then you press one of the presets 1-3 or the On/
Off button (this is a disguised installer default location so that
users will be less likely to reset this position). If you press the
Store button again, you will exit the store mode.
9.
To bring the loudspeakers into a preset position. Press the
zone button of the loudspeakers you want to control and
then press “On/Off” button or one of the preset locations 1-
3. All the speakers in that zone will then move to their preset
position.
10.
If you press the Power On/Off button the loudspeakers
will either be lowered into the room if they were closed be-
fore pressing the button or raised into the ceiling if the loud-
speakers were lowered into the room before the button was
pressed. Pressing the On/Off button momentarily to bring the
loudspeakers into the room returns them to the position they
were before the system was turned “off.”
11.
If you press and hold the On/Off Button for more than 3
seconds, the speakers in that zone will return to their dealer
preset positions.
12.
If you press and hold the Preset 3 Button for more than 3
seconds, the speakers will move so that the dog screws can
be accessed for installation or removal of the loudspeaker
from the ceiling.
Note:
If buttons on the remote are not pressed for 1 minute,
then the remote should go into a sleep mode until a button
is pushed.
Note:
Pressing the zone button for the first time, in any zone,
after power up, will cause the speakers in that zone to calibrate
themselves, which means that they will go to the 0 degree and
full counter-clockwise position.
Dip Sw Zone 1 Zone 2 Zone 3 Zone 4
0000 Spkr 1-8 None None None
0001 Spkr 1-5 Spkr 6,7 Spkr 8 None
0010 Spkr 1-7 Spkr 8 None None
0011 Spkr 1-6 Spkr 7,8 None None
0100 Spkr 1-2 Spkr 3-4 Spkr 5-6 Spkr 7-8
0101 Spkr 1-4 Spkr 5-8 None None
0110 Spkr 1-4 Spkr 5-6 Spkr 7-8 None
0111 Spkr 1-3 Spkr 4-5 Spkr 6-7 Spkr 8
• Speakers are in zones based on dip settings on control box as follows:
Time Remote Control Operations