SpeakerCraft SC2-100 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 27

SpeakerCraft SC2-100 Скачать руководство пользователя страница 15

15

SpeakerCraft – 1-800-472-5555 – 1-707-778-5733

2 Channel, BridgeaBle Power amPlifiers

INSTALLATION

LINE LEvEL AUdIO INpUT

CAuTIoN!

The amplifier must be off whenever you make changes

to the input connections.

CASCAdE AUdIO OUTpUTS

The “Cascade Audio Outputs” enable you to connect another amplifier to your
preamplifier output. The connectors are gold-plated RCA phono jacks. Connect
them to another amplifier’s inputs with a standard audio patch cable. The
outputs are not buffered; if you wish to daisy-chain more than 5 SpeakerCraft
2-Channel Amplifier amplifiers you will need a buffered distribution amplifier.

STEP

DESCRIPTION

1. Label all of the interconnecting cables

for the sources they connect to.

Use audio patch cables with RCA

phono plugs attached to the ends.

2. Connect the sources by inserting the

RCA plugs into the amplifier’s jacks.

Connect outputs from your sources

to inputs on the amplifier. Never

connect a source or preamplifier’s

input (e.g., record inputs) to

the inputs of your SpeakerCraft

2-Channel Amplifier.

«
...
13
14
15
16
17
...
»

Содержание SC2-100




























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды