background image

 

 

DFG460-4 

 

Operating Manual

 

SAFETY 

 

 

Only trained operatives should be allowed to work the

 DFG460

 range of floor grinders. 

 
Note: It is possible that the noise level produced by the Diamond Floor Grinder could exceed 
90dbA.  Appropriate PPE must be worn and the equipment must be used in line with 
guidelines laid down by the Health & Safety Executive. 
 
Always ensure that all power leads and hoses are disconnected before attempting to service 
the machine.   Never tip the machine backwards until the grinding plates have stopped 
rotating and the machine has been isolated at the main supply. 
 
Noise and vibration will occur at various levels dependent on the grinding attachments and work 
being completed. It is recommended that tests are taken on site to provide the operator with 
accurate information on using the equipment within the guidelines laid down by the Health & 
Safety Executive. 
 
 

NOTE: 

1.  NEVER OPERATE THE DFG460 FLOOR GRINDER OUTDOORS IN WET CONDITIONS AS 

THE ELECTRICAL COMPONENTS ARE NOT WATERPROOF 

2.  NEVER OPERATE THE DFG460 WITH THE HEADS RAISED FROM THE FLOOR 
3.  THE  SERVICE  OF  ELECTRICAL  COMPONENTS  SHOULD  BE  CARRIED  OUT  BY 

AUTHORISED PERSONNEL ONLY. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание DFG460-4























Отзывы: