SPALDING SPA0366 Скачать руководство пользователя страница 26

Страница: 26 / 26

SAFETY LABELS

www.Spalding.com

NOTICE

APPLY THE SAFETY LABELS TO THE COMPLETED ASSEMBLY PRIOR TO USE.

500080 04/21

MOVING SYSTEM

HEIGHT

ADJUSTMENT

1. While holding pole, rotate basketball sytem

forward until wheels engage with ground.

2. Move basketball system to desired location.

3. Carefully rotate basketball system upright.

4. Check system for stability.

Owner must ensure that all players know

and follow these rules for safe operation

of the system.

WARNING

• DO NOT hang on the rim or any part of

the system including

backboard, support braces, or net.

• During play, especially when performing

dunk type activities, use

caution to keep face away from the

backboard, rim, and net. Serious injury

could occur if teeth/face come in

contact with backboard, rim, or net.

• DO NOT slide, climb, shake, or play on

base and/or pole.

• After full assembly, fill system

completely with water or sand. Never

leave system in an upright position

without filling base with weight, as

system may tip over, causing injuries

and/or property damage.

• DO NOT add ballast on top of base

(such as sand bags or cinder blocks).

Such added ballast can crack base,

causing leakage, which could cause

system to tip over. DO NOT use ballast

on top of base as substitute for filling

base with water or sand.

• When adjusting height or moving

system, keep hands and fingers away

from moving parts.

• DO NOT allow children to move or

adjust system.

• DO NOT wear jewelry during play (rings,

watches, necklaces, etc.). Objects may

entangle in net.

• Surface beneath the base must be

smooth and free of gravel or other

sharp objects. Punctures or cracks in

base could result, causing leakage

which could cause system to tip over.

• Keep organic material and water away

from pole base. Grass, water, litter, etc.

could cause corrosion and/or

deterioration.

• Keep pole top covered with cap at all

times. Water and debris entering pole

through uncapped top can cause

corrosion from the inside.

• CHECK pole system for signs of

corrosion (rust, pitting, chipping) and

repaint with exterior enamel paint. If

rust has penetrated through the steel

anywhere, replace pole immediately.

• CHECK system before each use for

proper ballast, loose hardware,

excessive wear, and signs of corrosion;

replace or repair before use.

• CHECK system before each use for

instability.

• DO NOT use or leave system upright

during windy and/or adverse weather

conditions; system may tip over. Place

system in the storage position and/or in

an area protected from the wind and

weather, and free from personal

property and/or overhead wires.

• Never play on damaged equipment.

• See instruction manual for proper

assembly and maintenance.

• When moving system, use caution to

keep height adjust mechanism from

shifting.

• Do not allow water in tank to freeze.

During sub-freezing weather add 2

gallons of non-toxic antifreeze or sand,

or empty tank completely and store.

(Do not use salt.)

• DO NOT allow anyone to stand or sit on

base while moving system.

• DO NOT leave system unsupervised, or

play on system when wheels are

engaged for moving.

• Use caution when moving system

across uneven surfaces. System may

tip over.

• Use extreme caution if placing system

on sloped surface. System may tip over.

READ AND UNDERSTAND WARNINGS

LISTED BELOW BEFORE USING THIS

PRODUCT.
FAILURE TO FOLLOW THESE

WARNINGS MAY RESULT IN SERIOUS

INJURY AND/OR PROPERTY DAMAGE.

ID#: 500081 04/21

Trademarks registered in

the USA and other countries.

In the U.S.: 1-800-558-5234

In Canada: 1-800-284-8339

In Australia: 1-300-367-582

ATTENTION: CE PANNEAU ET CET ANNEAU NE

SONT PAS CONÇUS POUR SUPPORTER UN

JOUEUR SUSPENDU À L'ANNEAU OU AU FILET. LE

NON-RESPECT DE CETTE MISE EN GARDE PEUT

ENTRAÎNER DES BLESSURES CORPORELLES ET /

OU DES DOMMAGES MATÉRIELS.

MISE EN GARDE :

THIS BACKBOARD AND RIM IS NOT DESIGNED

TO SUPPORT A PLAYER HANGING FROM THE

RIM OR NET. FAILURE TO OBSERVE THIS

CAUTION MAY CAUSE BODILY INJURY AND /

OR PROPERTY DAMAGE

CAUTION:

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY

THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT:

LES ÉTIQUETTES D’ADVERTISSEMENT ET LES INSTRUCTIONS

DOIVENT ACCOMPAGNER CE PRODUIT. POUR UN REMPLACEMENT,

APPELEZ LE NUMÉRO SANS FRAIS :

1.800.558.5234 | www.huffysports.com

www.spalding.com

French and English general statement

English only - board warning

French only - board warning

Australian only - board warning

ATTENTION: CE PANNEAU ET CET ANNEAU NE

SONT PAS CONÇUS POUR SUPPORTER UN

JOUEUR SUSPENDU À L'ANNEAU OU AU FILET. LE

NON-RESPECT DE CETTE MISE EN GARDE PEUT

ENTRAÎNER DES BLESSURES CORPORELLES ET /

OU DES DOMMAGES MATÉRIELS.

MISE EN GARDE :

THIS BACKBOARD AND RIM IS NOT DESIGNED

TO SUPPORT A PLAYER HANGING FROM THE

RIM OR NET. FAILURE TO OBSERVE THIS

CAUTION MAY CAUSE BODILY INJURY AND /

OR PROPERTY DAMAGE

CAUTION:

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY

THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT:

LES ÉTIQUETTES D’ADVERTISSEMENT ET LES INSTRUCTIONS

DOIVENT ACCOMPAGNER CE PRODUIT. POUR UN REMPLACEMENT,

APPELEZ LE NUMÉRO SANS FRAIS :

1.800.558.5234 | www.huffysports.com

www.spalding.com

French and English general statement

English only - board warning

French only - board warning

Australian only - board warning

ATTENTION: CE PANNEAU ET CET ANNEAU NE

SONT PAS CONÇUS POUR SUPPORTER UN

JOUEUR SUSPENDU À L'ANNEAU OU AU FILET. LE

NON-RESPECT DE CETTE MISE EN GARDE PEUT

ENTRAÎNER DES BLESSURES CORPORELLES ET /

OU DES DOMMAGES MATÉRIELS.

MISE EN GARDE :

THIS BACKBOARD AND RIM IS NOT DESIGNED

TO SUPPORT A PLAYER HANGING FROM THE

RIM OR NET. FAILURE TO OBSERVE THIS

CAUTION MAY CAUSE BODILY INJURY AND /

OR PROPERTY DAMAGE

CAUTION:

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY

THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT:

LES ÉTIQUETTES D’ADVERTISSEMENT ET LES INSTRUCTIONS

DOIVENT ACCOMPAGNER CE PRODUIT. POUR UN REMPLACEMENT,

APPELEZ LE NUMÉRO SANS FRAIS :

1.800.558.5234 | www.huffysports.com

www.spalding.com

French and English general statement

English only - board warning

French only - board warning

Australian only - board warning

ATTENTION: CE PANNEAU ET CET ANNEAU NE

SONT PAS CONÇUS POUR SUPPORTER UN

JOUEUR SUSPENDU À L'ANNEAU OU AU FILET. LE

NON-RESPECT DE CETTE MISE EN GARDE PEUT

ENTRAÎNER DES BLESSURES CORPORELLES ET /

OU DES DOMMAGES MATÉRIELS.

MISE EN GARDE :

THIS BACKBOARD AND RIM IS NOT DESIGNED

TO SUPPORT A PLAYER HANGING FROM THE

RIM OR NET. FAILURE TO OBSERVE THIS

CAUTION MAY CAUSE BODILY INJURY AND /

OR PROPERTY DAMAGE

CAUTION:

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY

THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT:

LES ÉTIQUETTES D’ADVERTISSEMENT ET LES INSTRUCTIONS

DOIVENT ACCOMPAGNER CE PRODUIT. POUR UN REMPLACEMENT,

APPELEZ LE NUMÉRO SANS FRAIS :

1.800.558.5234 | www.huffysports.com

www.spalding.com

French and English general statement

English only - board warning

French only - board warning

Australian only - board warning

Содержание SPA0366



























Результаты поиска

Содержание SPA0366

Отзывы:

Похожие инструкции для SPA0366

Бренды по названию

Популярные бренды

SPALDING SPA0366, Руководство пользователя

Результаты поиска

Содержание SPA0366

Отзывы:

Похожие инструкции для SPA0366

Бренды по названию

Популярные бренды