Page 10
Advanced Preparations:
1. Read the entire installation guide and users manual thoroughly, understand instructions and warnings.
2. Be familiar with the controls of the range hood by reading through
Range Hood Operations
,
Page 13.
3. Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (please refer
the product label for the suitable voltage of this unit) and verify no debris has entered the vent openings, then
turn on the range hood. Verify all operations of the range hood by referring to
Range Hood Operations
,
Page
13.
4. Place all supplied parts and required hardware on a flat, stable surface and verify the existence of all supplied parts
listed on Page 4.
5.
Carefully remove the white plastic protective coat from the chimney covers and range hood.
Preparations:
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
1. Determine and mark the center line on the ceiling where the range hood will be installed. Make sure there is
proper clearance within the ceiling or wall for exhaust vent.
2. Due to the weight and size of this unit, please make sure that the support system or framework being used is stable
and secure in the ceiling.
3. Put a thick, protective covering over counter top, cook top or range to protect from damage or dirt. Remove any
hazardous objects around the area when installing.
4. Mark the locations of the support mounting bracket holes, vent cutout (if used) and power supply cable cutout
on the ceiling. Use drill and saber saw or keyhole saw to cut openings for power supply cable and vent (see
Venting requirements
and
Electrical requirements
, Pages 5-8).
5.
If venting to the outside install vent system (see
Venting Methods
, Page 7). Use caulking to seal exterior wall or
roof openings.
6.
Disconnect main electrical supply, prepare and run electrical wiring through ceiling. Leave approximately 12” of
electrical cord hanging from the ceiling. Do not restore power until wiring is completed.
7.
Disconnect power cord, remove the aluminum filter by pressing on the latch and gently pull the aluminum filter
down.
8. If charcoal filter is present, unscrew the two screws and remove the filter.
9. Set aside the aluminum filters and charcoal filter until the range hood is properly installed.
10.
If the range hood comes with a glass canopy and has not already been mounted to the hood, loosen the four
canopy screws and washers from the hood top, carefully place the canopy on the hood top, and loosely tighten
the four canopy screws along with washers. DO NOT put excessive pressure against the glass.
WARNING
Severe Injury
Rotating fan can cause
severe injury. Stay clear of
fan when motor is running.
WARNING
Severe Injury
Hood may have very shape edges. Please wear
protective gloves if it is necessary to remove
any parts for installing, cleaning or servicing.
Preparation
WARNING
Excessive Weight
Require three or more person to move and
install this range hood. Spinal or other bodily
injuries could occur if it is not followed.
Page 11
Installation: Wall Hoods
This range hood come with mounting brackets, one main and one or two additional for the chimney cover.
The range hoods shall be placed at a distance of 28-31” from the cooking surface for best performance. See
Page 5.
b) Drill three Ø8 mm holes in a horizontal line at the appropriate height for installation of the mounting bracket.
c) Insert brick anchor bolts (drywall anchor) into the holes , fix the mounting bracket on the wall, then secure
the cooker hood to it see Pic 2.
d) Install the 6” vent with the dampers into the duct connector of the range hood with 4 screws (4x8mm).see
below.
e) Install the 6” metal duct onto the vent, use aluminum tape to seal it and metal tie to secure it.
f) Put the two ( lower and upper) decorative duct cover on the hood, then adjust the inner duct cover to the
appointed height, see Pic5; drill two Ø8 mm holes in a horizontal line for installation of the other mounting
bracket and then attach the upper bracket . (Note: The hood can be installed on drywall and brick wall) Raise
the upper hood cover into its mounting position see. Secure the duct cover to the mounting bracket with the
screw provided in the box.
Screw
