Spaceman SM-6650 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

Spaceman SM-6650 Скачать руководство пользователя страница 16

www.spacemanusa.com

Phone: (720) 328-1020

Email: [email protected]

Freeze product

1. Verify cylinder is full of mixed product

2. Turn power switch to FREEZE

3. The motor will begin to agitate the

product, and the cooling system will
begin to freeze the product

4. Freezing product takes approximately 10

minutes; product is at the adjusted
viscosity when the flat sensor arm is
switched to the RIGHT

5. When the product reaches the desired

viscosity, it is ready to dispense

Dispense product

1. OPEN draw handle (RIGHT) until the desired

amount is dispensed

2. CLOSE the draw handle (LEFT) when finished

dispensing

CLOSED

OPEN

15

NOTE: If machine doesn’t turn on, turn power switch OFF, wait
30 minutes, and repeat steps 1 to 4. If problem persists, contact
service team.

CAUTION: If machine makes any abnormal noise during reset,
immediately turn power switch OFF and contact service team.

IMPORTANT: Machine shuts down automatically if cylinder experiences freeze-up (usually because
the viscosity is set too high for the selected product to prevent motor damage.

Use the green reset button on the machine’s back panel to return the machine to normal operation.

Proper Machine Reset
1.  Turn power switch to OFF
2.  Firmly press green reset button
3.  Wait 15 to 20 minutes.
4.  Turn power switch to WASH
5.  Observe machine performance

Frozen Product Operation

Machine power reset

«
...
14
15
16
17
18
...
»

Содержание SM-6650

























Отзывы:

Нет отзывов