manualshive.com logo in svg

Spaceman 6455-C, Руководство пользователя, Страница: 14 / 16

Поделиться
Скачать
Spaceman 6455-C Скачать руководство пользователя страница 14

 

13

 

Located directly above the draw valve, this arm tells the machine when product is being dispensed 

and how firm the product is. Beater and cooling systems are turned on and off based on 

information from the sensor arms. 

 

The viscosity adjustment, located behind the faceplate, 

controls the firmness of dispensed product. The higher the 

viscosity, the more firm the product. Viscosity settings 

should NOT need continuous adjustment.

 

Take off the faceplate. Viscosity

 

is

 

from

 

Softer

 

to

 

Harder 

from

 

level

 

1

 - 

6. Make small adjustments each time, and 

allow at least 10 to 15 minutes between adjustments to 

evaluate product firmness.

 

Adjust Product Consistency

 

Manage Sensor Arms

 

Arm moves up and down and 

tells machine when product is 

being dispensed. 

 

It moves UP when draw handle 

is in the OPEN position.

 

Flat arm moves left and right and 

tells machine when product is at 

desired consistency. 

 

Switched RIGHT means consistency 

is correct. Switched LEFT or IN THE 

MIDDLE means consistency is not 

yet correct.

 

  Hard           Soft

 

Operating Control

 

NOTE: 

If machine doesn’t turn on, turn power switch 

OFF, wait 30 minutes, and repeat steps 1 to 4. If 

problem persists, contact service team.

 

CAUTION: 

If machine makes any abnormal noise 

during reset, immediately turn power switch OFF 

and contact service team.

 

IMPORTANT: Machine shuts 

down automatically if cylinder 

experiences freeze

-

up 

(usually 

because the viscosity is set too 

high for the selected product to 

prevent motor damage.

 

Use the green reset button on 

the machine’s back panel to 

return the machine to normal 

operation.

 

Proper Machine Reset

 

1.

 

Turn power switch to OFF.

 

2.

 

Firmly press green reset button.

 

3.

 

Wait 15 to 20 minutes.

 

4.

 

Turn power switch to WASH.

 

5.

 

Observe machine performance.

 

Machine Power Reset

 

Spinner

 

Spinner operation is controlled by the paddle switch on lower portion of the 

spinner mount. 

 

The paddle switch is designed for one

-

hand operation. Hold cup up towards 

the spindle while pressing in the paddle switch with the same hand. Spinner 

will turn on and stay on. Spinner will stop as soon as paddle switch is released.

 

Содержание 6455-C

















Отзывы:

Нет отзывов