Space-Ray VF80-L5 DSI Скачать руководство пользователя страница 6

Form No. 43539480 

 

 

May 2021 

5

 

 

3.0)

 

GENERAL INFORMATION 

 

This  is  a  self-contained  agricultural  air  heater  for  use  in  locations  where  flammable  gases  or  vapors  are  not 
generally  present  and  is  intended  for  heating  of  agricultural  animal  confinement  buildings.  The  intended  use  is 
heating of agricultural animal confinement buildings. 

 

INSTALLATION REQUIREMENTS 
Installation  of this heater must be in  accordance with  all applicable codes shown  in  the instructions and/or the 
local  codes  and  authorities  having  jurisdiction.  In  the  UK  all  equipment  must  be  installed  and  maintained  in 
accordance with the relevant provisions of the Gas Safety (Installations and Use) Regulations 1998 for gas fired 
products. Installation practices must take into account the Health and Safety at Works Act 1974 or relevant codes 
of practice. In addition the installation must be carried out in accordance with the current IEE wiring regulations BS 
7671-latest revision, BS 6896-latest revision (Industrial & Commercial) and any other relevant British Standards 
and  Codes  of  Practice  by  a  qualified  installer.  All  external  wiring  MUST  comply  with  the  current  IEE  wiring 
regulations. 
Clearances  to  combustibles  as  outlined  in  the  manual  should  always  be  observed.  In  areas  used  for  storage of 

combustible materials where they may be stacked below the heater, the installer must post signs that will “specify 

the maximum permissible stacking height to ma

intain the required clearances from the heater to combustibles.”

 

Every heater shall be located with respect to building construction and other equipment so as to permit access to 
the control housing.  Each  installer shall use skillful and reliable installation  practices when  locating  the heaters 
and must give consideration to service accessibility. 
This  heater  is  for  either  INDOOR  or  OUTDOOR  INSTALLATION  and  is  used  in  an  UNVENTED  mode.  The  term 

Unvented 

actually  means 

Indirect  Vented

.  While  the  products  of  combustion  are  expelled  into  the  building, 

national codes require ventilation in the building to dilute these products of combustion. This ventilation must be 
provided by gravity or mechanical means. Ventilation requirements are addressed further in these instructions. 
Although these heaters may be used in many applications other than space heating (e.g., process heating), Space-
Ray will not recognize the warranty for any use other than space heating. 
This  heater  is  not  an  explosion  proof  heater.  Where  the  possibility  of  exposure  to  volatile  and  low  flash  point 
materials exists, it could result in property damage or death. This heater must not be installed in  a spray booth 
where the heater can operate during the spraying process. Consult your local fire marshal or insurance company. 
Before installation, check that the local distribution conditions, nature of gas and pressure, and adjustment of the 
appliance are compatible. 
 
This heater must be applied and operated under the general concepts of reasonable use and installed using best 
building practices. 
 
It is the responsibility of the qualified installer to supply the appropriate lifting equipment to safely install the 
agricultural air heater. Tools required for the safe installation, startup and maintenance are various screwdrivers, 
wrenches, pipe wrenches, volt and multi-meter, air and gas manometer and required tools to safely install the 
chosen hanging materials. 
 

This appliance can be used by children aged from 8 years and above and persons with 
reduced physical, sensory or mental capabilities or lack of experience and knowledge if 
they have been given supervision or instruction concerning use of the appliance in a 
safe way and understand the hazards involved. Children shall not play with the 
appliance. Cleaning and user maintenance shall not be made by children without 
supervision. 
 
Children must be supervised not to play with the appliance. 

 
 
 
 
 
 
 

Содержание VF80-L5 DSI







































Отзывы: