background image

 

Form No. 43539500 

 

July 2021 A

 

 
 
 
 

       LOW PROFILE RADIANT GAS BROODER 

 

MODELS:

 

 

 LPBL42-N5 / LPBL42-L5 with DIRECT SPARK IGNITION

 

 

 

 

INSTALLATION 

AND OPERATION 

INSTRUCTIONS 

 

 

 

 

 

 

 

 

 

    

Patent Pending 

 

OWNER/INSTALLER: 

  For  your  safety  this  manual  must  be  carefully  read  before  installing,  operating  or 

servicing this brooder.  This brooder is intended for use with either Natural Gas or Propane Gas.  It must be 
installed by a qualified service person or a licensed contractor in accordance with state and local codes.  In 
the absence of these codes, the installation must conform to the National Fuel Gas Code ANSI Z223.1 (latest 
edition) also know a NFPA54 or the CAN/CGA-B149.1/2 Installation Code in Canada. 

 

WARNING:

  Improper installation, adjustment, alteration, service or maintenance can cause injury, property 

damage  or  death.    Refer  to  this  manual.    For  assistance  or  additional  information,  consult  a  qualified 
installer, service agency or the gas supplier.  

 

INSPECT

 all combustion air openings into the building and, if necessary, clear as they become blocked by 

litter, dust, feathers or other matter. 

 

INSPECT

 and clean the brooder filters on a regular basis to allow proper brooder operation. 

 

 

 

FOR  YOUR  SAFETY:

    EXHAUST  FANS 

MUST

  be  operating  on  an  appropriate  cycle  when  brooders  are 

operating to avoid a high concentration of carbon monoxide.  When used without fresh air, this brooder may 
give off carbon monoxide, an odorless and poisonous gas.  

CARBON MONOXIDE POISONING MAY LEAD TO 

DEATH.

  Early signs of carbon monoxide poisoning resemble the flu with headaches, dizziness and nausea.  If 

you experience these signs, 

GET FRESH AIR IMMEDIATELY!

  Have the brooders serviced as soon as possible 

and check the ventilation in the house.   

 

 

 

These brooders are designed for agricultural applications and may operate with the use of either Natural Gas 

or  Liquid  Propane  (LP)  Gas.    Check  the  brooder’s  nameplate  to  determine  the  correct  gas  type  before 

proceeding with installation. 

 

 

 

IF YOU SMELL GAS: 

 

!

 

DO NOT

 try to light any appliance. 

!

 

DO NOT

 touch any electrical switch; do not use any 

telephone in your building. 

!

  IMMEDIATELY

  call  your  gas  supplier  from  a  neighbor's 

telephone.    Follow  the  gas  supplier's  instructions.    If  you 
cannot reach your gas supplier, call the fire department. 

 

 

 

 

DO NOT 

store or use gasoline or other 

flammable vapors and liquids in the 
vicinity of this or any other appliance. 
 

SAVE THIS MANUAL 

FOR FUTURE REFERENCE.

 

 

 

 
 
 
 

FOR YOUR SAFETY 

Scan warranty QR code on the right to 
register your product. 

 

Содержание LoPro LPBH40-L5

































Отзывы: