SP Scientific FTS Systems BioCool 80 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

SP Scientific FTS Systems BioCool 80 Скачать руководство пользователя страница 23

FTS Systems BioCool™ 80

Operation

Rev 002, 08/12

15

© SP Scientific 2012

Magnetic Stirrer

To operate the magnetic stirrer:

Activate the magnetic stirrer by rotating the Fluid Stir Control Dial clockwise.

1.

Adjust the rotational speed of the stirrer by turning the Fluid Stir Control Dial

2.

clockwise (to increase the speed) and/or counterclockwise (to decrease the

speed).

To deactivate the stirrer, rotate the Fluid Stir Control Dial counterclockwise.

3.

The magnetic stirrer may be turned on or off at any time for procedural purposes, but

in general, the unit should not be operated without stirring. If the reservoir fluid is not

agitated, the fluid may exhibit thermal variations. SP Scientific recommends setting

the Fluid Stir control dial to its maximum speed at all times for optimal operation and

performance.

Note:

Do not operate the magnetic stirrer without fluid in the reservoir.

Powering Off

To power off the BioCool™ 80:

Toggle the on/off breaker switch to the Off position.

1.

The green indicator light will turn off and the BioCool™ 80’s refrigeration

2.

system compressor(s) will stop.

Note:

When the BioCool™ 80 is not in use, ensure that the bath reservoir lid is closed

to prevent evaporation of the cooling fluid.

Restarting

Due to the nature of the refrigeration system and its compressor, the BioCool™ 80

should never be restarted immediately after it is powered off. SP Scientific

recommends waiting approximately five (5) minutes between shutting down and

restarting the BioCool™ 80.

Fluid Stir Control Dial

«
...
21
22
23
24
25
...
»

Содержание FTS Systems BioCool 80





































Отзывы:

Нет отзывов