background image

 

Quick Start Reference Sheet

Panasonic PT-LB10VU

Revision A

 

03/28/05 

SP Controls reserves the right to modify specifications without notice at any time.

 

 

NOTE:

 This one-page document is intended 

only as a quick reference for installation

 – please read 

the SP Controls Application Note for a complete description of this projector driver prior to installation. 

I. Driver Features 

 1. Input Selection Mapping

 

Selection 1: 

VIDEO 

Selection 2: 

S-VIDEO 

Selection 3: 

RGB 

Selection 4: 

NETWORK 

 
 2. Hidden Function Mapping (Default Configuration) 

Using the ON button as a shift key, press the following buttons to access the specified projector features.

 

Selection 1: 

AV MUTE 

Selection 2: 

ENTER 

Selection 3: 

ADJUST LEFT 

Selection 4: 

ADJUST RIGHT 

Off: 

MENU  

Volume Up: 

ADJUST UP 

Volume Down: 

ADJUST DOWN 

 
 3. Other Driver Features 

Power Status Feedback Method

  RS-232 Power Polling   

Control Wiring: 

RS-232 

and 

IR-Emitter  

II. Wiring Specifications 

 
NOTE

: The Panasonic PT-LB10VU projector serial port is a female 8-pin mini-DIN. This document 

provides instructions for terminating the RS-232 control cable directly onto an 8-pin mini-DIN connector. If 
you wish to terminate the control cable on a standard DB9 connector, an adaptor cable may be 
separately ordered from Panasonic (Panasonic part no. 

ET-ADSER

).  

 

1. RS-232:  

    Wire the Panel RS-232 port to a male 8-pin mini-DIN as follows: 

RX to  5 

TX to  3 

GND to  4 

     Connect this male DB9 to the projector port labeled 

SERIAL

.  

 

2. Infrared Emitter:  

     Wire the Panel IR/Serial port to a female 1/8" Mini as follows: 

IR/SER

 to 

tip

 

GND

 to 

ring

 

     Connect to the included IR Emitter and attach the emitter bud to any projector IR window. 

 

  
 
 
 
 
 

Содержание PT-LB10VU






Отзывы: