SOYO 5XBE5 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 47

SOYO 5XBE5 Скачать руководство пользователя страница 34

30

BIOS Setup

PM Control by
APM

Choose

Yes

or

No

(default). APM stands for

Advanced Power Management. To use APM,
you must run Òpower.exeÓ under DOS v6.0 or
later version.

Video Off Method

Choose

V/H Sync+Blank

(default),

Blank

screen

, or

DPMS

for the selected PM mode.

Video Off After

Choose

Standby

(default),

Suspend

,

Doze

, or

N/A mode

.

Modem Use IRQ

Choose Modem IRQ Setting.

Doze Mode

When the set time has elapsed, the BIOS sends
a command to the system to enter doze mode
(system clock drops to 33MHz). Time is
adjustable from 1 Min to 1 Hour.

Standby Mode

The default is Disabled. Time is adjustable
from 1 Min to 1 Hour.

Suspend Mode

The default is Disabled. Only an SL-Enhanced
(or SMI) CPU can enter this mode. Time is
adjustable from 1 Min to 1 Hour. Under
Suspend mode, the CPU stops completely (no
instructions are executed.)

HDD Power Down

When the set time has elapsed, the BIOS sends
a command to the HDD to power down, which
turns off the motor. Time is adjustable from 1
to 15 minutes. The default setting is Disabled.
Some older model HDDs may not support this
advanced function.

Soft-Off by PWR-
BTTN

Choose

Instant-off

(default) or

Delay 4 Sec

.

Delay 4 Sec

turns off the system power 4

seconds after pushing the power button

VGA Active
Monitor

Choose Enabled (default) or Disabled.
Enabled Ð enables the power management

timers when a Òno activityÓ event
is detected.

«
...
32
33
34
35
36
...
»

Содержание 5XBE5
















































Отзывы:

Нет отзывов