V091028
N.O.
N.C.
COM
Door SEN
PB
AL
M
V+
V-
A+
B-
V-
V+
B-
A+
WG
0
WG
1
BZ
GLED
RLED
V-
+12V
+12V
V-
N.C.
N.O.
RS-232
USB
WG1WG0 BZ LED
GR
LED
RED V- V+
12V
CTL
COM
N.O
N.C
RS-485
RS-232
RS-485
USB
or
N.O.
COM
N.C.
TTL
GND
P1
P2
P3
P4
Fingerprint & Finger Vein
LCD Access Controller
Diagram
Manu Tree
5. Tools
1. Language
2. Master Code
3. Master Range
4. Terminal Port
5. AR401RO16 Node
6. Open Time Zone
7. Informations
8. Clock Setting
6. Quit
7. Quit & Arming
4. Parameters[2]
1. Auto Relock
2. Egress(R.T.E)
3. Attendance
4. Master Node
5. Force Open
6. Close & Stop
7. Anti-pass-back
8. Duress Code
9. Check User FP
3. Parameters[1]
1. Node ID
2. Auto open Zone
3. Door Relay Tm
4. Door Close Tm
5. Alarm Relay Tm
6. Alarm Delay Tm
7. Arming Delay Tm
8. Arming PWD
2. User Setting
1. Password
2. Access Mode
3. Extend Options
4. Single Floor
5. Multi Floor
6. Enroll FP
7. Delete FP
1. Add/ Delete
1. Add > Card ID
2. Add > RF Learn
3. Suspend > Address
4. Suspend > ID #
5. Delete > Address
6. Delete > ID #
7. Recover > Address
8. Recover > ID #
9. Antipass Group
Programming
A. Keyboard Lock/ Unlock
Lock/ Unlock
At the same time according to and keyboard can be locked, and then press once to unlock.
1. System will automatically exit from Programming Mode when inactivating for 30 seconds.
2. LED status indicates controller’s mode and status.
Busy (red) – blinking constantly when operates in Programming Mode
– or flashing an existed card in card learn mode, it comes 2 beeps warning and LCD panel displays “Same Card: user address / card number”
Error (red) – invalid card with 2 beeps warning and LCD panel displays “Card Number Err!”
– or in anti-pass-back mode, when violates the access, it comes one beep warning and LCD panel displays “Anti-pass Error!”
Arming (green) – arming on status
Alarm (red) – any abnormal condition occurs
3. Keypad will be locked up when constantly entering incorrect pin code or master code.
4. Maximum error times of pin code and master code can be changed via the software 701Server (default: 3 times)
B. Entering and Exiting Programming Mode
Entering
Input 123456 or PPPPPP
[i.e.] The Default Value= 123456. If already changed the Master Code= 876112, input
876112
→
Access programming mode
P.S.If within
30 sec.
entering no instruction, it will automatically leave the programming mode.
Exiting
Press the repeatedly
→
Quit
→
then press to confirm
6
Changing the Master Code
Access programming mode
→
Tools
→
Master Code
→
Input the 6-digit new master code
→
Succeeded
5
2
C. Initial setup
Changing the Node ID of Reader
Access programming mode
→
Parameters[1]
→
Node ID
→
Input New Node ID:1~254
(default value: 001)
→
Input: 1~4 to Show Card ID
in which format?
(1.No, 2.WG, 3.ABA, 4.HEX)
→
Succeeded
3
1
Changing the Language
Access programming mode
→
Tools
→
Language
→
EN
→
Succeeded
→
Initial system...
5
1
1
Strike Lock
Bolt Lock
(Magnet Lock)
Lock Power
Converter
Power
Magnetic Door Contacts
Thick Green
Thick Blue
Blue
Green
Pink
Brown
Yellow
Push Button
