28
Add one Transponder (Card / Key Tag) to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 9 * 0 0 0 0 1 *
User Number
0 0 0 0 1 #
Quantity
Present the transponder near the unit. (Set random transponder one by one). A
green light and beep means that the transponder was accepted.
Step3: Press * #
Add a series of Transponders (Card / Key Tag) to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 9 * 0 0 0 0 1 *
User Number
0 0 0 1 0 #
Quantity
Present the lowest card code of transponder to the unit in the desired order (set
sequential transponder once and make a careful record of which transponders
are assigned to which user numbers).
Step3: Press * #
29
Add a User Code to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 2 * 0 0 0 0 1 *
User Number
2 0 8 1 #
User Code
The user number 00001 can access the door by just either flash card or entering the
user number 00001, then entering 2081#.
OR Enter 1 3 * 0 0 0 0 1 *
User Number
2 0 8 1 #
User Code
The user number 00001 can access the door by using flash card and entering
2081#.
Note: A user code must be 4 digits. If the user code has leading zeros, they must be
entered as this example show “0008”.
Step3: Press * #
Delete a Transponder / User Code from the system
Step1: Press * and master code fallow an #
Step2: Enter 1 0 * 0 0 0 0 1 *
Starting User Number 1
0 0 0 0 1 #
Ending User Number 1
A green light and beep means that the transponder / user
code was deleted.
Step3: Press * #
Delete a range of Transponders / User Code from the system
Step1: Press * and master code fallow an #
Step2: Enter 1 0 * 0 0 0 0 1 *
Starting User Number 1
0 0 0 1 0 #
Ending User Number 10
A green light and beep means that the range of transponders / user codes were
deleted.
Step3: Press * #
30
Delete all Transponders
Step1: Press * and master code fallow an #
Step2: Enter 2 9 * 2 9 * #
The LED flash red during 10 seconds to mean that the system is deleting all
transponders / user codes. Then a green light and beep means that all transponders
/ user codes were deleted.
Step3: Press * #
Enable a Transponder to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 1 * 0 0 0 0 1 *
Starting User Number 1
0 0 0 0 1 #
Ending User Number 1
A green light and beep means that the transponder is enabled.
Step3: Press * #
Enable a range of Transponder to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 1 * 0 0 0 0 1 *
Starting User Number 1
0 0 0 1 0 #
Ending User Number 10
A green light and beep means that the range of transponders are enabled.
Step3: Press * #
31
15. Mode 8 Easy Guide
Add one Transponder (Card / Key Tag) to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 9 * 0 0 0 0 1 *
User Number
0 0 0 0 1 #
Quantity
Present the transponder near the unit. (Set random transponder one by one).
A green light and beep means that the transponder was accepted.
Step3: Press * #
Add a User Code to the system
Step1: Press * and master code fallow an #
Step2: Enter 1 2 * 0 0 0 0 1 *
User Number
2 0 8 1 #
User Code
The user number 00001 can access the door by just either flash card or entering
2081.
OR Enter 1 3 * 0 0 0 0 1 *
User Number
2 0 8 1 #
User Code
The user number 00001 can access the door by using flash card and entering
2081#.
Note: A user code must be 4 digits. If the user code has leading zeros, they must
be entered as this example show “0008”.
Step3: Press * #
Other operation is same as AR-721H4 Easy Guide, for example, enter/ exit the
programming mode, change master code, door relay release time, add / delete
/ enable one or many transponder and so on.
