Sovereign SCS 2000, Руководство по эксплуатации

Страница: 9 / 20

9
Packaging
The unit is supplied in packaging to prevent it from
being damaged in transit. The raw materials in this
packaging can be reused or recycled.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage.
앬 Read the operating instructions carefully and
comply with them at all times. It is important to
consult these instructions in order to acquaint
yourself with the unit, its proper use and the
important safety regulations.
앬
Keep this manual in a safe place, so that the
information is available at all times.
앬
If you give the equipment to any other person,
make sure that you pass on these operating
instructions as well.
We can accept no liability for damage or
accidents which arise due to non-compliance
with these instructions.
1. Safety information
Make sure you read through all of the safety
information before using the device for the first time.
Chainsaws are dangerous tools which can cause fatal
injuries if used without due care and attention.
Explanation of the symbols on the machine
(Fig. 27):
1. Read the operating instructions.
2. Wear safety goggles.
3. Wear ear protectors.
4. Never expose the device to rain.
5. If the cable is damaged or cut, disconnect the
power plug from the mains immediately.
6. Maximum cutting depth.
General safety instructions
Workplace
Keep your work area clean and tidy. Untidy
and unlit work areas can result in accidents.
Never use electric power tools in an area
where there is a risk of explosion or where
there are inflammable liquids, gases or dust.
Electric power tools generate sparks that can
ignite the dust or vapors.
Keep children and other people away from
the electric power tool whilst you are using it.
If you are distracted you may lose control of the
tool.
Electrical safety
The plug on the tool must fit into the socket. The
socket must not be modified in any way. Do not
use adapter plugs together with power tools with
a protective earth. Unmodified plugs and
matching sockets will reduce the risk of an
electric shock.
Avoid bodily contact with earthed components
e.g. pipes, radiators, stoves or refrigerators.
There is an increased risk of suffering an electric
shock if your body is earthed.
Keep the tool out of the rain and away from
moisture. The ingress of water into an electric
power tool increases the risk of an electric shock.
Do not use the cable for a purpose for which it is
not designed, for example to carry the tool or to
pull the plug out of the socket. Keep the cable
away from heat, oil, sharp edges and moving
parts. Cables that are damaged or caught up
increase the risk of an electric shock.
If you use an electric power tool outdoors, use
only extension cables that are approved for
outdoor use. The use of an extension cable which
is suitable for outdoor use reduces the risk of an
electric shock.
Do not use an electric power tool if the switch is
defective. An electric power tool that cannot be
switched on or off is dangerous and must be
repaired.
The device can be connected to any 230V mains
outlet. However, the socket outlet must have a
protective earthing contact and must be protected
by an automatic cutout (max. 16 A). Additionally,
a residual current device (RCD) circuit-breaker
with max. 30 mA must be used!
To prevent danger, damaged power cables must
be replaced by the manufacturer or by a service
company authorized to carry out the work by the
manufacturer.
Safety of persons
Be careful, watch what you are doing and be
sensible and responsible when using an
electric power tool. Never use the tool if you
are tired or under the influence of drugs,
alcohol or medication.
A single moment of
carelessness when using the electric power tool
could be all it takes to cause a serious injury.
Wear personal safety equipment and always
wear safety goggles.
Wearing protective
equipment like a dust mask, non-slip safety
shoes, a protective helmet or hearing protection
can also reduce the risk of injury.
Make sure that the tool cannot start up
accidentally. Check that the switch is NOT
switched on before you insert the plug into