background image

16

Southworth Products

Mortuary Lift Manual

7.1    Securing the Lift for Maintenance

The maintenance device supplied with this lift is designed to support 

the unloaded platform as shown. Any other use of the maintenance 

device may cause failure of the maintenance device and could cause 

serious injury or death.
Lifts equipped with roller transfer platforms are not equipped with 

maintenance devices. All maintenance to be perform with the lift in the 

lowered position.

7.1.1.  Lifts Equipped Standard or Ball Transfer Platforms

To properly secure the lift for maintenance:

1.  Lower the lift to the fully lowered position.
2. 

Engage the floor lock to prevent unintended movement of the lift during maintenance.

3.  Disconnect the power source to prevent unintended operation of the lift during 

maintenance.

4.  Lift up on the roller end (the end closest to the push bar) of the platform and hinge it up 

high enough to lift the maintenance bar into position. Platform weight: Approximately 162 lb.

5.  Lift the maintenance bar up and lower the platform onto the maintenance bar. 

LIFT MUST BE IN FULLY LOWERED POSITION

HINGE PLATFORM PLATFORM UP

RAISE MAINTENANCE 

DEVICE

PLATFORM LOWERED ONTO 

MAINTENANCE DEVICE

Содержание CLL05-68


























Отзывы: