AL20RSW&AL60RSW&
AL60CSW&AL100CSW
ALWAYS READ INSTRUCTIONS BEFORE USING POWER LIGHTS
WARNING
Users of this product are cautioned not to make modifications or changes that are not approved by Southwire Company, LLC. Doing so may void
the compliance of this product with applicable laws and regulatory requirements and may result in the loss of the user’s authority to operate the
equipment.
PRODUCT COMPLIANCE
Using Instructions
For AL20RSW, AL60RSW:
• Before using, plug the charger into any 100~240V AC standard power source to let unit fully charge until the battery volume bar at the
back of the light reach to 100%.
• Press the “ ”button to turn on or turn off the light.
• Press the “ ” or “ ”button to adjust the brightness.
• Press the button “ ” to activate the power bank function, the power bank indicator light will turn on, then use an USB cable to
connect the mobile device you want to charge. Press the button “ ” again to close power bank function, and the indicator will light off.
Power bank output: 5V 1A.
• Press “ ” or “ ” to activate battery capacity indicator.
• The light will flash as a low power warning prior to the battery running out.
For AL60CSW, AL100CSW:
• Before using, plug the unit into any 100~240V AC standard power source. The “ ” indicator will light when connect successfully.
• Press the button “ ” to turn on or turn off the light.
• Press button “ ” or “ ” to adjust the brightness.
• Power bank function: use a USB cable to connect the digital device you want to charge.
Power bank output: 5V 1A.
BLUETOOTH CONTROL FOR BRIGHTNESS
FOR AL60RSW, AL60CSW and AL100CSW
From either the “
” or “
”, download the Southwire application to your smart phone or tablet.
Step 1: Press the button “ ” on the lamp to turn on the light.
Step 2: Turn on Bluetooth on your smartphone or tablet.
Step 3: Open Southwire application and select “ ” tab.
Any available Southwire Bluetooth lamp will appear on the screen.
• Choose the lamps you want to control, up to 4 lights.
• Press “ ” to change the name of the light (optional).
• One light can be controlled by two devices at the same time.
Step 4: Select “ ” tab and slide vertically on the screen to adjust the brightness of the lamp.
Step 5: Select “OFF” tab to turn off the light.
THE BLUETOOTH® WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED BY BLUETOOTH SIG, INC. AND ANY USE OF
SUCH MARKS BY AEC IS UNDER LICENSE.
GET IT ON
UNITED STATES AND CANADA
FCC Statement :
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed
and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
CAUTION: To comply with the limits of the Class B device, pursuant to Part 15 of the FCC Rules, this device is to comply with Class B limits.
All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables is likely to result in
interference and reception of the device.
