Southern States SO17542STA Скачать руководство пользователя страница 24

24

00811

00663

Retaining 
Ring

Washers

Square Key
(Rear Wheel Only)

Axle 
Cover

FRONT WHEEL TOE-IN/CAM BER

The front wheel toe-in and camber are not 
adjustable on your tractor.  If dam age has 
occurred to affect the front wheel toe-in or 
camber, contact your nearest authorized 
service center/de part ment. 

TO AD JUST STEER ING WHEEL ALIGN-
 MENT

If steering wheel crossbars are not 
hor i zon tal (left to right) when wheels are 
positioned straight forward, remove steer-
 ing wheel and reassemble with crossbars 
horizontal. Tighten securely.

TO REMOVE WHEEL FOR REPAIRS 

1.   Block up axle securely.
2.   Remove axle cover, retaining ring and 

washers to allow wheel removal (rear 
wheels have a square key - Do not 
lose).

3.   Repair tire and reassemble.

NOTE:

 On rear wheels only:  align 

grooves in rear wheel hub and axle.  Insert 
square key.
4.   Replace washers and snap retaining 

ring securely in axle groove.

5.   Replace axle cover.

NOTE: 

To seal tire punctures and pre vent 

fl at tires due to slow leaks, tire sealant 
may be purchased from your local parts 
dealer. Tire sealant also pre vents tire dry 
rot and corrosion.

TO START ENGINE WITH A WEAK 
BAT TERY 

 WARNING:

  Lead-acid batteries 

gen er ate ex plo sive gases.  Keep sparks, 
fl ame and smoking ma te ri als away from 
bat ter ies.  Always wear eye pro tec tion 
when around batteries.
If your battery is too weak to start the en-
gine, it should be recharged. (See "BAT-
TERY" in the MAINTENANCE section of 
this man u al).
If “jumper ca bles” are used for emer gen cy 
starting, follow this pro ce dure:

IMPORTANT

:  Your tractor is equipped 

with a 12 volt system. The other vehicle 
must also be a 12 volt system. Do not use 
your tractor battery to start other vehicles. 

TO ATTACH JUMPER CABLES -
1.   Connect one end of the RED cable 

to the POSITIVE (+) terminal of each 
battery(A-B), taking care not to short 
against tractor chassis.

2.   Connect one end of the BLACK ca ble 

to the NEGA TIVE (-) terminal (C) of 
fully charged battery.

3.   Connect the other end of the BLACK 

cable (D) to good chassis ground,  
away from fuel tank and bat tery.

TO REMOVE CABLES, REVERSE 
ORDER -
1.   BLACK cable fi rst from chassis and 

then from the fully charged battery.

2.   RED cable last from both batteries.

02614

Weak or Dead
Battery

Fully Charged
Battery

Center 
Span
Keeper

Transaxle 
Pulley

Stationary 
Idler

Clutching 
Idler

Engine 
Pulley

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание SO17542STA

















































Отзывы: