manualshive.com logo in svg

Southern States SO1742STA, Руководство пользователя, Страница: 22 / 48

Поделиться
Скачать
Southern States SO1742STA Скачать руководство пользователя страница 22

22

Both Front Links Should be Equal in Length

Nut “F”

Ground Line

Bottom edge of 
mower to ground

Suspension Arm

Lift Link Adjustment Nut

Bottom edge of  
mower to ground

A

A

FRONT-TO-BACK ADJUSTMENT 

IMPORTANT:

  Deck must be level side-to 

side. If the following front-to-back adjust-
ment is necessary, be sure to adjust both 
front links equally so mower will stay level 
side-to-side.    

 

Trunnion

Front Links

Nut “E”

“D”

“D”

Mandrel

To obtain the best cutting results, the 
mower housing should be adjusted so 
that the front is approximately 1/8" to 1/2" 
lower than the rear when the mower is in 
its highest position.
Check adjustment on right side of trac-
 tor.  Measure dis tance “D” directly in front 
and behind the mandrel at bottom edge of 
mower housing as shown.
•   Before making any necessary ad just -

ments, check that both front links are 
equal in length.  

•   If links are not equal in length, adjust 

one link to same length as other link.

•   To lower front of mower loosen nut “E” 

on both front links an equal number of 
turns.

•   When distance “D” is 1/8" to 1/2" 

lower at front than rear, tighten nuts “F” 
against trunnion on both front links.

•   To raise front of mower, loos en nut “F” 

from trunnion on both front links. Tighten 
nut “E” on both front links an equal num-
ber of turns. The two front links must 
remain equal in length.

•   When distance “D” is 1/8" to 1/2" lower 

at front than rear, tighten nut “F” against 
trun nion on both front links.

•   Recheck side-to-side ad just ment.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked 
on level ground or driveway.  Make sure 
tires are properly infl ated (See “PROD-
 UCT SPECIFICATIONS” section of this 
man u al).   If tires are over or underinfl ated, 
you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT 
•   Raise mower to its highest position.
•   At the midpoint of both sides of mower, 

measure height from bot tom edge of 
mower to ground.   Distance “A” on both 
sides of mower should be the same or 
within 1/4" of each other.

•   If adjustment is necessary, make adjust-

ment on one side of mower only.

•   To raise one side of mower, tighten lift 

link ad just ment nut on that side.

•   To lower one side of mower, loosen lift 

link ad just ment nut on that side.

NOTE

:  Each full turn of adjustment nut 

will change mower height about 1/8".
•   Recheck measurements after ad just ing.

TO REMOVE MOWER 

Mower will be easier to remove from the 
right side of tractor.
1.   Place attachment clutch in “DIS EN-

GAGED” position.

2.   Move attachment lift lever forward to 

low er mower to its lowest po si tion.

3.   Roll belt off engine pulley.
4.   Remove small retainer spring, and 

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание SO1742STA

















































Отзывы:

Нет отзывов