South-Tek Systems Quick-Check 10 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 29

South-Tek Systems Quick-Check 10 Скачать руководство пользователя страница 23

Quick-Check PowerSaver Manifold 10 & 20 Port South-Tek
Systems

Revision: 0
Revision Date: 8/30/17

Page 23 of 29

Figure 22: Zone Setup Screen

Figure 23: Initial System Purge

“Legend” button. Press inside the box to change the number to the number of zones that will be required for the
system. This screen can be seen in Figure 22.

8.

(Optional) Change the name of the zones in “Zone Setup” which can be accessed through the “Menu”. The user
can press any zone to change each to a more descriptive name of up to 8 characters.

7.1.2

Initial System Purge

When  a  Fire  Protection  System  is  first  filled  with  nitrogen,  it
mixes  atmospheric air  within the  pipes and fittings.  In order
to  get  pipes  down  to  an  acceptable  purity  level,  the
AutoPurge  System  should  be  used.  The  Quick-Check’s
PowerSaver Manifold will vent out a small amount of gas to
eventually lower oxygen purity to a suitable level. To account
for the amount of time it will take for the system to get within
the  parameters  of  the  setpoint,  the  user  can  engage  Initial
System  Purge.  This  allows  40  days  (default)  of  purging
without alarm.

To  set  up  the  Initial  System  Purge,  open  the  “Zone  Setup”
screen  found  in  the  “Menu”,  then  press  “Start-Up  Settings”
and the screen in Figure 23 will be displayed. User must turn
Initial System Purge on with the selector switch to the right of
the “Initial System Purge (Days)” to start it. Before conducting
this step, Initial System Purge(Days) can be set  by the user by pressing in the  box next to it (factory default  = 40
days).
This feature will automatically turn off once the “Days left in Initial System Purge” reaches 0, but it may be turned off
manually at any point by pressing the toggle switch again.

7.1.3

Normal Start-up

Follow this procedure to start the Quick-Check for normal operation. If this is the first time the unit has been started,
follow the Initial Start-Up procedure above, otherwise:

1.

Open all APS zone ball valves and ensure all APS flow tuning is correct according to the APS Tuning Sheet.

2.

Toggle the “ON/OFF” button on the “Home” screen to the “ON” position to start the system

NOTE: If the generator or any part of the system has been opened to the atmosphere or water, the system must be
purged of any residual air/water to get within the limits of the purity setpoint. Another “Initial System Purge” is
advised.

7.2

SHUTDOWN

For normal shutdown, toggle the “ON/OFF” button to OFF on the “Home” screen.
WARNING: The Quick-Check PowerSaver Manifold will remain pressurized after shutdown. Before performing any
maintenance or opening any piping systems, always depressurize the system. Failure to do so may result in injuries.

«
...
21
22
23
24
25
...
»

Содержание Quick-Check 10






























Отзывы:

Нет отзывов