manualshive.com logo in svg

South bend SB1049F, Руководство пользователя

Поделиться
Скачать
South bend SB1049F Скачать руководство пользователя страница 2

Model SB1049F

Page 1 of 4

Model SB1049F

Heavy 13 - 13" x 30" Gearhead Lathe with

Fagor DRO

Product Dimensions

Weight........................................................................................................................................................... 1881 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 90 x 38 x 69 in.
Footprint (Length x Width)........................................................................................................... 80-3/4 x 19-1/2 in.

Shipping Dimensions

Type.......................................................................................................................................................... Wood Crate
Content.......................................................................................................................................................... Machine
Weight........................................................................................................................................................... 2472 lbs.
Length x Width x Height................................................................................................................... 43 x 78 x 73 in.

Electrical

Power Requirement......................................................................................................... 220V, Single-Phase, 60 Hz
Full-Load Current Rating............................................................................................................................... 19.45A
Minimum Circuit Size.......................................................................................................................................... 30A
Connection Type..................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. No
Recommended Power Cord............................................................................. "S"-Type, 3-Wire, 12 AWG, 300 VAC
Plug Included.......................................................................................................................................................... No
Recommended Plug Type.................................................................................................................................. L6-30
Switch Type....................................................................................... Control Panel w/Magnetic Switch Protection

Motors

Main

Type............................................................................................................. TEFC Capacitor-Start Induction
Horsepower............................................................................................................................................... 3 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 19A
Speed................................................................................................................................................ 1725 RPM
Power Transfer ............................................................................................................................ V-Belt Drive
Bearings................................................................................................ Shielded & Permanently Lubricated

Coolant Pump

Type............................................................................................. TEFC Capacitor-Start Induction (Class F)
Horsepower............................................................................................................................................ 1/8 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................ 0.45A
Speed................................................................................................................................................ 3450 RPM
Power Transfer ............................................................................................................................ Direct Drive
Bearings................................................................................................ Shielded & Permanently Lubricated

-2-

Mfd. Since 12/13

Model SB1049F

M A N U A L   I N S E R T

Содержание SB1049F









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды