South bend SB1049F Скачать руководство пользователя

Страница: 1 / 136

Manual Insert

PHONE: (360) 734-1540 •

www.southbendlathe.com

MODEL SB1049F HEAVY-13

13" X 30" GEARHEAD LATHE w/DRO

WARNING: No portion of this manual may be reproduced without written approval.

#TS16215 Printed in Taiwan

The Model SB1049F Lathe is the same machine as the Model SB1049 except for the following:

• Added a 2-Axis Fagor Digital Readout (DRO).

Except for the differences noted in this insert, all other content in the Model SB1049 Owner’s Manual

applies to this machine. Before operating your new lathe, you MUST read and understand this insert,

the entire Model SB1049 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of

injury when using this machine. Keep this insert for later reference.

If you have any further questions about this manual insert or the differences between the Model

SB1049F and the Model SB1049, contact our Technical Support at (360) 734-1540 or email

[email protected].

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1570

PSB1049F1570

DRO ASSEMBLY FAGOR 2-AXIS

1570-3 PSB1049F1570-3 DRO Y-AXIS SCALE FAGOR MKT-27

1570-1 PSB1049F1570-1 DRO DISPLAY FAGOR 20-iT

1615

PSB1049F1615

MACHINE ID LABEL

1570-2 PSB1049F1570-2 DRO X-AXIS SCALE FAGOR MKT-102

1620

PSB1049F1620

MODEL NUMBER BRASS PLATE

New & Changed Parts

1620

1615

1570

1570-1

1570-3

1570-2

SB1049F

V1.12.13

Содержание SB1049F









































































































































Результаты поиска

Содержание SB1049F

Отзывы:

Похожие инструкции для SB1049F

Бренды по названию

Популярные бренды

South bend SB1049F, Руководство пользователя

Результаты поиска

Содержание SB1049F

Отзывы:

Похожие инструкции для SB1049F

Бренды по названию

Популярные бренды