AUTO TACH/ TACHLESS LEARNING
Start the vehicle with
the ignition key.
2 CHIRPS/ 2 FLASHES = TACH MODE
NOTES:
When tach learning the system first sends out a request for tach from the data port. If it gets a
valid rpm response over 750 rpm then it goes into data tach mode (3 flashes). If there is no
response, the unit will look for the tach/tachless.
Once the starter goes on then off, the unit will learn tach, if there is no tach detected within a few
seconds after starting, the system will learn in tachless mode after 20 seconds.
If there is no starter detected, the system learns tach after 30 seconds. If no tach is detected the
system will learn tachless after an additional 10 seconds.
4 CHIRPS/ 4 FLASHES = TACHLESS MODE
3 CHIRPS/ 3 FLASHES = DATA TACH MODE
SYSTEM PROGRAMMING -
Menu 1
PAGE 6
INSTALL MANUAL
SYSTEM WIRING DETAILS
HYBRID MODE‘S
Hybrid mode 1 -
This option requires a tach connection. Once the vehicle starts the system will not monitor
the tach input and stay running for 15 minutes.
Hybrid Mode 2-
(No Tach wire connection)This setting will power up the ignition wires, pulse the start output
for 2 seconds then stay on/ run for 15 minutes. See Program Menu 4, Hybrid Mode 1& 2. Hybrid mode 2 was
designed for
hybrid vehicles that may not actually start until the battery voltage
drops.
**Hybrid Mode 2
is also ideal for vehicles with no starter wire or “Automatic Starting”. This is when the
vehicle’s starter motor will continue to crank and start the vehicle even if the key is only turned to the start
position momentarily.
“Push to Start” systems and
Hold the brake then start the vehicle with the key. Place the transmission into reverse to lower the
RPM. Press and release the button on the antenna twice. The system will chirp the Horn and
flash the park lights two times to confirm Tach Mode or chirp 4 times/ 4 flashes to indicate
Tachless Mode re-learn.
LOW IDLE LEARNING
ARS.1
Press Lock
Press Unlock
Press Start
Press #
MENU 1
MENU 2
MENU 3
MENU 4
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time. The park lights will turn on and the Siren
will chip to confirm entering program mode.
3 - Select the Program Menu by pressing...
ENTERING PROGRAM MODE
1 -
Cycle the Ignition Key On/Off On/Off On (
Leaving the key ON
)
2 -
Press and
RELEASE
the Program Switch 1 time and the park light will turn on.
(Horn/ Siren will chip to confirm program mode has been entered)
3 -
Press and
HOLD
the Program Switch for 5 seconds or until the Park Lights flash 3 times.
4 - Turn the ignition key
OFF
to exit.
(
Confirmed by 3 Park Lights flashes/ Siren chirps)
SYSTEM RESET
The system will confirm the program menu by flashing the park lights/ horn / siren chirps.
4 - Press and Release the Program Switch to advance through the settings.
(
Confirmed by Park Lights/ Siren chirps & LED flashes)
5 - Press and hold the Program Switch to change the setting
.
(
Confirmed by Park Lights/ Siren chirps & LED flashes)
6 -
To exit Program Mode, turn the key off.
(Confirmed by Long Siren Chirp)
Example- Programming Menu 1, Setting 6 to 2nd Unlock.
1 - Cycle the Ignition Key On/Off On/Off On
2 - Press and release the Program Switch 1 time. (1 chirp/ 1 flash)
3- Press and release the Lock button for Menu 1. (1 chirp/ 1 flash)
4- Press and release the program button until the LEDs on the antenna flash 6 times.
**The park lights will flash and the siren will chirp 6 times to confirm the current setting)
5- Press and hold the program button. The Park Light will flash once (option 1), pause
then flash twice to confirm option 2 has been selected.
**The siren will chirp 1 time (option 1) then 2 times to confirm the option 2.
6- Release the program switch and turn off key to exit.
SYSTEM PROGRAMMING -
Menu 1
PAGE 7
INSTALL MANUAL
PROGRAM MODE
ARS.1
