1.800.338.7337 / www.soundoffsignal.com
3
Setting PA Volume:
1. PA Volume Control (see
Input Settings
, 1-3)
If set to “Programmed”
2. Press and Hold Auxiliary Button #1 and #2 until LEVEL #2
and LEVEL #3 LED flashes.
a. Depress and hold PA switch on microphone and press
Pushbutton 1-6 depending on volume required. When
correct volume is determined, press Radio Rebroadcast
and the volume setting will be permanently stored.
If set to “RR Button Adjustable”
3. Momentarily press RR Button to select PA Volume. PA Volume
will be displayed on indicators below RR Button.
1-(LOW)
2
3
4
5-(HIGH)
LOW 2
5
4
3
HIGH
HANDHELD REMOTE
PSRNHHC(x)
PSRNHHCI 2.19.14
Tones Program:
1.
Press and Hold Buttons #2 and #5 until Level 1, Level 2 and
Level 3 LEDs flash.
2.
Press SIREN button to program the tones (each press of the
SIREN button will advance to next TONE mode). Note:
in operation, each press of the SIREN button will scroll
between the 3 programmed tones.
3.
SIREN
Mode
SIREN LED:
Siren Tone #1
PWR LED:
Siren Tone #2
SIREN LED and PWR LED:
Siren Tone #3
4.
Press Auxiliary Buttons to get required tone
POWER LED
SIREN LED
HORN LED
MANUAL LED
CONDITION
ON
FLASHING
ON
ON
OVER-TEMPERATURE (380R ONLY)
ON
FLASHING
OFF
ON
UNDER-VOLTAGE
ON
FLASHING
ON
OFF
OVER-VOLTAGE
ON
FLASHING
FLASHING
-
COMM FAULT - RELAY
ON
FLASHING
-
FLASHING
COMM FAULT - AMP
ON
FLASHING
FLASHING
FLASHING
COMM FAULT -RELAY AND AMP
ON
OFF
-
-
STANDBY MODE
OFF
ON
ON
-
SPKR 1 IS ACTIVE
OFF
ON
OFF
-
SPKR 1 IS NOT-FUNCTIONING
OFF
ON
-
ON
SPKR 2 IS ACTIVE
OFF
ON
-
OFF
SPKR 2 IS NOT-FUNCTIONING
SIREN AMPLIFIER DIAGNOSTIC
INDICATORS:
LED INDICATOR
CONDITION
OFF
RELAY OUTPUT IS OFF
ON
RELAY OUTPUT IS ON
FLASHING
RELAY OUTPUT HAS A FAULT
AUXILILARY AND LEVEL SWITCH LED
INDICATORS:
AUX
BUTTON #4
AUX
BUTTON #5
AUX
BUTTON #6
PRIMARY
SPKR 1 TONE
SECONDARY
SPKR 2 TONE
OFF
OFF
OFF
Disabled
Disabled
OFF
OFF
ON
WAIL 1
WAIL 2
OFF
ON
OFF
Yelp 1
Yelp 2
OFF
ON
ON
ALERT A
YELP 1
ON
OFF
OFF
Piercer 1
Yelp 1
ON
OFF
ON
HiLo
Super HiLo Tone
ON
ON
OFF
Super HiLo Tone
Super HiLo Tone
ON
ON
ON
Cycle Tone
(Wail 1, Yelp 1, Alert A, Piercer)
Cycle Tone
(Yelp 1, Alert A, Piercer, Yelp 1)
Tone #1
5.
HORN Button:
Press Horn Button and HORN 1 LED will turn ON
Press Auxiliary Buttons to get required tone.
6.
Man Button:
Press MAN Button and MANUAL LED will turn ON
Press Auxiliary Buttons to get required tone.
MANUAL BUTTON TONE DURATION
MOMENTARY: When played solo
LATCHED: When played over other tones.
