1.800.338.7337 / www.soundoffsignal.com
Slide Switch Mode:
1. Press and Hold Auxiliary Button #1 and #4 until Level 2 LED
flashes.
2. Press Auxiliary switch 1, 2, or 3 depending on required mode of
operation.
Aux 1: Progressive 1,2,3
Level 1 selected: Active Outputs: 1
Level 2 selected: Active Outputs: 1,2
Level 3 selected: Active Outputs: 1,2,3
Aux: 2 Progressive 1,2,3 with option to turn off lower levels
Level 1 selected: Active Outputs: 1
Level 2 selected: Active Outputs: 1,2 (Level 1 may be turned OFF)
Level 3 selected: Active Outputs: 1,2,3 (Level 1 and 2 may be
turned OFF)
Aux 3: Individual 1,2,3
Level 1 selected: Active Outputs: 1
Level 2 selected: Active Outputs: 2
Level 3 selected: Active Outputs: 3
Toggle
ON/OFF
Momentary
ON
8
Second
Delay
Left
Arrow
Right
Arrow
Center Out - Arrow
Alley
Left
Alley
Right
Single
Button
Arrow
Single
Button
Alley
4. Press and release Auxiliary Button until desired mode is
selected.
5. Continue steps 2-4 for any other Auxiliary Buttons needing to
be programmed.
LEGEND:
ON =
Denotes Factory Default Setting
HANDHELD REMOTE
PSRNHHC(x)
PSRNHHC1
PSRNHHC2
1
PROGRAMMING MANUAL
NOTE:
For All programming modes: Momentarily depress Radio
Rebroadcast push-button to save and exit.
To hear samples of all the tones available go to
www.soundoffsignal.com website.
Programming Modes
Auxiliary Button Programming:
1. Press and Hold Auxiliary Button #1 and #6 until Level 1 LED Flashes.
2. Press the auxiliary button which setting is going to be viewed/
changed.
3. Monitor the Arrow/Alley LED’s to determine setting for Auxiliary
Button
Input Settings:
1. Press and Hold Auxiliary Button #1 and #3 until LEVEL #3
LED flashes.
1
. Park Kill Polarity Mode: Determines what voltage level will
activate park kill functions. Disables AUX Input
ON = Activated when Ground is applied to Park
Kill input wire.
OFF = Activate when +V is applied to Park Kill
input wire
2
. Horn Ring Polarity Mode: Determines what voltage level will
activate Horn Ring functions.
ON = Activated when Ground is applied to Horn
Ring input wire.
OFF = Activated when +V is applied to Horn
Ring input wire.
3
. PA Volume Control (see Setting PA Volume)
ON = RR Button Adjustable
OFF = Programmed
4
. Level 3 Tone Activation : Determines when the siren tone
push-buttons on control panel are enabled.
ON = Tone push buttons always enabled
OFF = Tone push button only enabled with slide
switch is in position #3.
5
. 8 Second Buzzer alert: Provides audible beep when
ever any auxiliary switches are ON or level 1, 2 or 3
is active.
ON = Enabled
OFF = Disabled
PSRNHHCI 2.19.14
IMPORTANT INFORMATION:
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/sales-support
.
If you have questions regarding this product, contact
Technical Services
, Monday - Friday, 8 a.m. to 5 p.m. at
1.800338.7337
(press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to
.
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
CONTROLS THESE SIREN AMPS:
ETSA380R
ETSA385HR
ETSA461HPP
ETSA462HPP
ETSA461HPP-EXT
ETSA462HPP-EXT
PSRN4ANR1
PSRN4ANR2
6
. Air Horn Button Output Channels
ON = In standby mode, Air Horn tone is
output on Spkr A & B. When Warning
Tone is Active, Warning Tone continues
on Spkr A & Air Horn Button Tone is
output on Spkr B
OFF = Air Horn Button Tone always
produced on Spkr A & B.
